SimpleCANBreakoutMicro
jlpoltrack·SimpleCANBreakoutMicro
About the SimpleCANBreakoutMicro PCB
SimpleCANBreakoutMicro is an open source PCB design by jlpoltrack, published on GitHub under the MIT license. It is a 2-layer board measuring 20 × 15 mm, with 11 components from 7 distinct parts.
Other key parts include the XC6206PXXXMR and SN65HVD230. By type, the board carries 6 capacitors, 2 ICs, 2 connectors and 1 resistor.
It belongs with the rf & radio and dev boards & breakouts designs in this gallery.
From the project
Tiny 20x15 mm SN65HVD230 CAN transceiver breakout with JST-GH connector (KiCad)
A tiny (20 × 15 mm) CAN transceiver breakout. It converts a microcontroller's logic-level CAN TX/RX to a CAN bus on a JST-GH connector, with an onboard 3.3 V regulator and optional 120 Ω termination.
- SN65HVD230 3.3 V CAN transceiver, wired for high-speed mode (up to 1 Mbps) - XC6206 3.3 V LDO, so the board runs from a single 5 V supply - 120 Ω termination resistor, enabled by a solder jumper (open by default) - 2-layer, 1.6 mm PCB, parts on the top side only

Main components on the SimpleCANBreakoutMicro
SimpleCANBreakoutMicro bill of materials (BOM)
11 components, 7 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XC6206PXXXMR XC6206PxxxMR | SOT-23-3 | U2 |
| 1 | SN65HVD230 | SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | CONN_01X04_PIN Conn_01x04_Pin | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | CONN_01X04_PIN Conn_01x04_Pin | JST_GH_SM04B-GHS-TB_04x1.25mm_Angled | J2 |
| 3 | 1u | C_0603_1608Metric | C1, C4, C5 |
| 3 | 100N 100n | C_0603_1608Metric | C2, C3, C6 |
| 1 | 120 | R_0603_1608Metric | R1 |
SimpleCANBreakoutMicro design files
The KiCad project lives in the jlpoltrack/SimpleCANBreakoutMicro repository on GitHub; these links point at the commit this page was built from.
SimpleCANBreakoutMicro: common questions
How big is the SimpleCANBreakoutMicro PCB?
The SimpleCANBreakoutMicro measures 20 × 15 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the SimpleCANBreakoutMicro?
11 components, from 7 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the SimpleCANBreakoutMicro design files?
From the jlpoltrack/SimpleCANBreakoutMicro repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the SimpleCANBreakoutMicro design in my own project?
Yes, under the terms of its MIT license, which jlpoltrack chose for the repository.
Similar boards
Breakout 112pin Connector
rusefi
174 × 58 mm39 parts2LGPL-3.01.2kEecv breakout
rusefi
140.8 × 53.7 mm9 parts4LGPL-3.01.2kBreakout 60pin EEC-IV
rusefi
139.7 × 62.2 mm15 parts2LGPL-3.01.2k134pin 7-967288-1
rusefi
139.7 × 73.7 mm38 parts2LGPL-3.01.2k88 Pin Vag Breakout
rusefi
142 × 58 mm91 parts2LGPL-3.01.2kRj45 breakout
rene-dev
15.2 × 53.8 mm3 parts2LGPL-3.0979