MacoEins
Joe-BN·MacoEins·Macropad_PCB/Macropad_PCB.kicad_pcb
About the MacoEins PCB
MacoEins is an open source ESP32 PCB design by Joe-BN, published on GitHub. It is a 2-layer board measuring 93.1 × 82.5 mm, with 28 components from 8 distinct parts.
Its main chip is the ESP32-C3_SUPERMINI_TH, from the ESP32 family. By type, the board carries 12 diodes, 10 switches, 4 resistors, 1 IC and 1 connector.
It belongs with the keyboards and robotics & motion designs in this gallery.
From the project
A customizable macropad powered by the Esp32 c3 microcontroller.
First iteration of the macropad project.

Main components on the MacoEins
MacoEins bill of materials (BOM)
28 components, 8 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3_SUPERMINI_TH | MODULE_ESP32-C3_SUPERMINI_TH | U1 |
| 1 | Battery Power connector | JST_EH_S2B-EH_1x02_P2.50mm_Horizontal | J1 |
| 9 | SW_MEC_5G | JBN_SW_Cherry_MX_1.00u_PCB | SW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8 +1 |
| 1 | RotaryEncoder | XDCR_PEC11R-4020F-S0024 | SW10 |
| 9 | D_45deg | D_DO-35_SOD27_P7.62mm_Horizontal | D1, D2, D3, D4, D5, D6, D7, D8 +1 |
| 3 | LED | LED_D5.0mm | D10, D11, D12 |
| 1 | 1K | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1 |
| 3 | 330 | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2, R3, R4 |
MacoEins design files
The KiCad project lives in the Joe-BN/MacoEins repository on GitHub; these links point at the commit this page was built from.
MacoEins: common questions
What microcontroller does the MacoEins use?
The MacoEins is built around the ESP32-C3_SUPERMINI_TH, from the ESP32 family.
How big is the MacoEins PCB?
The MacoEins measures 93.1 × 82.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the MacoEins?
28 components, from 8 distinct parts. The full bill of materials is listed on this page.
Where can I download the MacoEins design files?
From the Joe-BN/MacoEins repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the MacoEins design in my own project?
The repository has no license, so all rights stay with Joe-BN. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the MacoEins without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k