Lifepo4-battery monitor
JoeyBobbles·lifepo4-battery-monitor·hardware/schematic_breadboard.kicad_sch
About the Lifepo4-battery monitor PCB
Lifepo4-battery monitor is an open source AVR/Arduino PCB design by JoeyBobbles, published on GitHub under the MIT license. It is a board, with 4 components from 4 distinct parts.
Its main chip is the Arduino_Nano_v3.x, from the AVR/Arduino family. Other key parts include the INA228. By type, the board carries 1 IC, 1 module and 1 connector.
It belongs with the displays & leds, power & battery and dev boards & breakouts designs in this gallery.
From the project
Experimental Arduino Nano LiFePO4 battery monitor with INA228 sensing, OLED display and KiCad schematics.
Experimental Arduino Nano monitor for two 12.8 V, 8 Ah LiFePO4 batteries in parallel (16 Ah nominal). The firmware reads an INA228 voltage/current sensor and drives an SH1106 128 × 64 I²C OLED.
- Samples voltage, current and power every 500 ms. - Offers live readings/uptime and capacity pages, switched by a debounced D3 button. - Integrates current to estimate amp-hours used and remaining; positive current means discharge and negative current means charge. - Reports readings and capacity estimates at 9600 baud and displays an error if the INA228 is absent at startup.
Main components on the Lifepo4-battery monitor
Lifepo4-battery monitor bill of materials (BOM)
4 components, 4 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | INA228 | VSSOP-10_3x3mm_P0.5mm | U1 |
| 1 | Arduino_Nano_v3.x | Arduino_Nano | A1 |
| 1 | Adafruit SPI FRAM 64Kbit | J1 | |
| 1 | u8g2 | 1.3"OLEDDisplayModule(128x64) |
Lifepo4-battery monitor design files
The KiCad project lives in the JoeyBobbles/lifepo4-battery-monitor repository on GitHub; these links point at the commit this page was built from.
Lifepo4-battery monitor: common questions
What microcontroller does the Lifepo4-battery monitor use?
The Lifepo4-battery monitor is built around the Arduino_Nano_v3.x, from the AVR/Arduino family.
How many components are on the Lifepo4-battery monitor?
4 components, from 4 distinct parts. The full bill of materials is listed on this page.
Where can I download the Lifepo4-battery monitor design files?
From the JoeyBobbles/lifepo4-battery-monitor repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Lifepo4-battery monitor design in my own project?
Yes, under the terms of its MIT license, which JoeyBobbles chose for the repository.
Can I test firmware for the Lifepo4-battery monitor without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k