ESPCord
JudasLilith·ESPCord·hardware/ESPCord/ESPCord.kicad_pcb
About the ESPCord PCB
ESPCord is an open source ESP32 PCB design by JudasLilith, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 17.4 × 29.9 mm, with 8 components from 6 distinct parts.
Its main chip is the ESP32-C3, from the ESP32 family. Other key parts include the AMS1117-3_3_C347222. By type, the board carries 2 ICs, 2 capacitors, 2 resistors, 1 connector and 1 relay.
It belongs with the iot & wireless designs in this gallery.
From the project
a power controller powered with the ESP32.
* An ESP32-based PCB to connect to Wall adapters for controlling power to SBCs.
* I normally use a small Raspberry Pi Zero in order for me to control my Octoprint setup, but due to the board being connected constantly it cannot shut down with the normal octoprint UI. This is when I thought that I should have a method of controlling the power going to the Setup, so that it can properly reboot every time I manipulate its power source by being connected to Home Assistant.

Main components on the ESPCord
ESPCord bill of materials (BOM)
8 components, 6 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3 Espressif Systems | QFN-32_EP_5x5_Pitch0.5mm | U1 |
| 1 | AMS1117-3_3_C347222 UMW(Youtai Semiconductor Co., Ltd.) | SOT-223-5 | U2 |
| 1 | USB_C_Receptacle | USB-C_16 | J1 |
| 1 | SRD-03VDC-SL-C Ningbo Songle Relay | SRD-03VDC-SL-C | K1 |
| 2 | EMK212ABJ106KG-T 10uF_0805_16V_lowESR Taiyo Yuden | C_0805 | C1, C2 |
| 2 | 5.1K | R_1206 | R3, R4 |
ESPCord design files
The KiCad project lives in the JudasLilith/ESPCord repository on GitHub; these links point at the commit this page was built from.
ESPCord: common questions
What microcontroller does the ESPCord use?
The ESPCord is built around the ESP32-C3, from the ESP32 family.
How big is the ESPCord PCB?
The ESPCord measures 17.4 × 29.9 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ESPCord?
8 components, from 6 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the ESPCord design files?
From the JudasLilith/ESPCord repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the ESPCord design in my own project?
Yes, under the terms of its GPL-3.0 license, which JudasLilith chose for the repository.
Can I test firmware for the ESPCord without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k