Rs repeater
Juvenile-Furry·eleken-pcb·rs_repeater/rs_repeater.kicad_pcb
About the Rs repeater PCB
Rs repeater is an open source RISC-V PCB design by Juvenile-Furry, published on GitHub. It is a 2-layer board measuring 50 × 17 mm, with 12 components from 10 distinct parts.
Its main chip is the CH32V002AxMx, from the RISC-V family. By type, the board carries 5 connectors, 3 diodes, 2 resistors, 1 IC and 1 capacitor.
From the project
プリント基板用
Main components on the Rs repeater
Rs repeater bill of materials (BOM)
12 components, 10 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CH32V002AxMx | STC_SOP-16_3.9x9.9mm_P1.27mm | U1 |
| 1 | PIN_IN | PinHeader_1x03_P2.54mm_Horizontal | J1 |
| 1 | SOC_IN | PinSocket_1x03_P2.54mm_Horizontal | J2 |
| 1 | PIN_OUT | PinHeader_1x03_P2.54mm_Horizontal | J3 |
| 1 | SOC_OUT | PinSocket_1x03_P2.54mm_Horizontal | J4 |
| 1 | write | PinHeader_1x03_P2.54mm_Vertical | J5 |
| 1 | D_Schottky | D_DO-41_SOD81_P7.62mm_Horizontal | D1 |
| 2 | LED | LED_D3.0mm | D2, D3 |
| 1 | 0.1u | C_Disc_D10.5mm_W5.0mm_P5.00mm | C1 |
| 2 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2 |
Rs repeater design files
The KiCad project lives in the Juvenile-Furry/eleken-pcb repository on GitHub; these links point at the commit this page was built from.
Rs repeater: common questions
What microcontroller does the Rs repeater use?
The Rs repeater is built around the CH32V002AxMx, from the RISC-V family.
How big is the Rs repeater PCB?
The Rs repeater measures 50 × 17 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Rs repeater?
12 components, from 10 distinct parts. The full bill of materials is listed on this page.
Where can I download the Rs repeater design files?
From the Juvenile-Furry/eleken-pcb repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Rs repeater design in my own project?
The repository has no license, so all rights stay with Juvenile-Furry. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Rs repeater without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RISC-V firmware against it before you order a PCB.
More boards in eleken-pcb
Rs torch
Juvenile-Furry
50 × 50 mm21 parts2LNo license2RISC-V
Rs note
Juvenile-Furry
50 × 50 mm15 parts2LNo license2Rs lever
Juvenile-Furry
47 × 44 mm9 parts2LNo license2Rs dust 4way
Juvenile-Furry
50 × 50 mm8 parts2LNo license2Rs light sensor
Juvenile-Furry
50 × 24 mm8 parts2LNo license2Rs lamp
Juvenile-Furry
47 × 24 mm6 parts2LNo license2Rs dust 2way
Juvenile-Furry
50 × 18 mm4 parts2LNo license2
Similar boards
RISC-V
Audio
byrantech
27.8 × 22.3 mm38 parts2LMIT4.3kRISC-V
Keybit
notaroomba
19.1 × 19.1 mm19 parts2LNo license438RISC-V
Workbench-1 Controller
Quchaosheng
160 × 130 mm106 parts8LApache-2.0212RISC-V
Froggyswadge
cnlohr
81.5 × 72.2 mm92 parts2LMIT105RISC-V
Keytartouch
cnlohr
152.5 × 117.5 mm69 parts2LMIT105RISC-V
Ch32v003f4u6 with wsled
cnlohr
40.6 × 44.5 mm26 parts2LMIT105