BLUEPILL
KabitaShahu·Circuit·BLUEPILL/BLUEPILL.kicad_pcb
About the BLUEPILL PCB
BLUEPILL is an open source STM32 PCB design by KabitaShahu, published on GitHub. It is a 2-layer board measuring 69.5 × 85.9 mm, with 35 components from 11 distinct parts.
Its main chip is the BluePill, from the STM32 family. By type, the board carries 15 resistors, 6 connectors, 6 diodes, 6 capacitors and 2 ICs.
Main components on the BLUEPILL
BLUEPILL bill of materials (BOM)
35 components, 11 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | BluePill | STM32_BLUEPLL_MOD | U1 |
| 1 | ~ | bno08 | U2 |
| 1 | Conn_01x04_Pin | PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | Conn_01x04_Pin | jst_4 | J6 |
| 1 | Conn_01x02_Pin | JST_EH_B2B-EH-A_1x02_P2.50mm_Vertical | J7 |
| 3 | Conn_01x05_Pin | JST_EH_B5B-EH-A_1x05_P2.50mm_Vertical | J8, J9, J10 |
| 6 | LED | LED_D3.0mm | D1, D2, D3, D4, D5, D6 |
| 1 | C | Capacitor_10uF | C1 |
| 1 | C | Capacitor_100uF | C2 |
| 4 | C | Capacitor_Disc_Small | C3, C4, C5, C6 |
| 15 | R | Resistor_small | R1, R2, R3, R4, R5, R6, R7, R8 +7 |
BLUEPILL design files
The KiCad project lives in the KabitaShahu/Circuit repository on GitHub; these links point at the commit this page was built from.
- LayoutBLUEPILL/BLUEPILL.kicad_pcb
- SchematicBLUEPILL/BLUEPILL.kicad_sch
BLUEPILL: common questions
What microcontroller does the BLUEPILL use?
The BLUEPILL is built around the BluePill, from the STM32 family.
How big is the BLUEPILL PCB?
The BLUEPILL measures 69.5 × 85.9 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the BLUEPILL?
35 components, from 11 distinct parts. The full bill of materials is listed on this page.
Where can I download the BLUEPILL design files?
From the KabitaShahu/Circuit repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the BLUEPILL design in my own project?
The repository has no license, so all rights stay with KabitaShahu. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the BLUEPILL without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in Circuit
Microscope
KabitaShahu
133 × 64.1 mm43 parts2LNo license0New pi pico
KabitaShahu
77.5 × 87.5 mm32 parts2LNo license0STM32
BLUEPILL NANO
KabitaShahu
67.5 × 74.4 mm27 parts2LNo license0Pi pico
KabitaShahu
70.8 × 94.1 mm27 parts2LNo license0Numatic optocoupler
KabitaShahu
52 × 55.3 mm24 parts2LNo license0Relay power supply
KabitaShahu
107.7 × 98.8 mm11 parts2LNo license0ESP32
ESP32-wrover
KabitaShahu
37.8 × 111.3 mm9 parts2LNo license0
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k