14 open source boards using the BluePill

Real designs built with the BluePill, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

14 boardsClear filters|Most starred

How designs wire the BluePill

Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the BluePill connects to, and the resistors, capacitors and other passives placed on it.

  • The 3V3 pin is tied to 5V on 7 of 8 designs.
  • The VBAT pin is left unconnected on 5 of 8 designs (a signal on 3).
  • The PC15 pin is left unconnected on 5 of 8 designs (a signal on 3).
  • The NRST pin is left unconnected on 5 of 7 designs (a signal on 2).
VBATpin 1Connected to: Not connected 63% · a signal 38%
PC15pin 4Connected to: Not connected 63% · a signal 38%
PB3pin 11, 31Connected to: A connector 50% · not connected 38%
  • Series resistor on 38% · 2 kΩ (1), 1.2 kΩ (1)
PB4pin 12, 32Connected to: A connector 56% · not connected 19%
  • Series resistor on 38% · 2 kΩ (1), 1.2 kΩ (1)
PB1pin 14, 34Connected to: A connector 31% · not connected 38%
  • Series resistor on 38% · 2 kΩ (1), 1.5 kΩ (1), 4.7 kΩ (1)
NRSTpin 17Connected to: Not connected 71% · a signal 29%
5Vpin 18Connected to: 3.3V 63% · not connected 25%
GNDpin 19, 20, 39, 40Connected to: GND 72% · 3.3V 19%
PB14_MISO2pin 23Connected to: Not connected 71% · a signal 29%
PA3pin 28Connected to: Not connected 63% · a signal 38%
PA15pin 30Connected to: Not connected 63% · a signal 38%
PB9pin 37Connected to: Not connected 63% · a signal 25%
3V3pin 38Connected to: 5V 88%

20 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Andes by niektb, Main board by Windfisch, Midikraken DIN board by Windfisch and Apeks by MiguelDeTrool.

The BluePill in open source designs

The gallery holds 14 open source boards using the BluePill from 10 GitHub repositories; a typical one measures about 86.4 × 95 mm and carries around 65 components.

93% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.

The most starred is !!UNTESTED!! by niektb.

Parts used alongside the BluePill

Microcontrollers on boards using the BluePill

What boards using the BluePill are built for

BluePill: common questions

Where can I find a BluePill reference design?

Each of the 14 boards on this page is a real design using the BluePill. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the BluePill 3V3 pin connected?

The 3V3 pin is tied to 5V on 7 of 8 designs. Counted from the KiCad layouts of 10 open source designs using the BluePill.

How is the BluePill VBAT pin connected?

The VBAT pin is left unconnected on 5 of 8 designs (a signal on 3). Counted from the KiCad layouts of 10 open source designs using the BluePill.

How is the BluePill PC15 pin connected?

The PC15 pin is left unconnected on 5 of 8 designs (a signal on 3). Counted from the KiCad layouts of 10 open source designs using the BluePill.

Which microcontrollers do boards using the BluePill use?

Most are built on STM32 (2) and ESP8266 (1).

How big is a typical board using the BluePill?

The median is 86.4 × 95 mm, and 93% are two-layer designs.

What is the most popular open source board using the BluePill?

By GitHub stars, !!UNTESTED!! by niektb, with 34 stars.

Can I simulate one of these boards using the BluePill before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part