BLUEPILL NANO
KabitaShahu·Circuit·BLUEPILL_NANO/BLUEPILL_NANO.kicad_pcb
About the BLUEPILL NANO PCB
BLUEPILL NANO is an open source STM32 PCB design by KabitaShahu, published on GitHub. It is a 2-layer board measuring 67.5 × 74.4 mm, with 27 components from 12 distinct parts.
Its main chip is the BluePill, from the STM32 family. By type, the board carries 11 resistors, 7 connectors, 6 capacitors, 2 diodes and 1 IC.
Main components on the BLUEPILL NANO
BLUEPILL NANO bill of materials (BOM)
27 components, 12 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | BluePill | STM32_BLUEPLL_MOD | U2 |
| 3 | Conn_01x05 | JST_EH_B5B-EH-A_1x05_P2.50mm_Vertical | J1, J2, J3 |
| 1 | Conn_01x04_Pin | jst_4 | J4 |
| 1 | Conn_01x04 | jst_4 | J5 |
| 1 | Conn_01x02_Pin | JST_EH_B2B-EH-A_1x02_P2.50mm_Vertical | J6 |
| 1 | Conn_01x04 | PinHeader_1x04_P2.54mm_Vertical | J7 |
| 2 | LED | LED_D3.0mm | D1, D2 |
| 1 | C | Capacitor_100uF | C1 |
| 3 | C_Polarized_US | Capacitor_Disc_Small | C2, C3, C4 |
| 1 | C | Capacitor_10uF | C5 |
| 1 | C | Capacitor_Disc_Small | C6 |
| 11 | R | Resistor_small | R1, R2, R3, R4, R5, R6, R7, R8 +3 |
BLUEPILL NANO design files
The KiCad project lives in the KabitaShahu/Circuit repository on GitHub; these links point at the commit this page was built from.
BLUEPILL NANO: common questions
What microcontroller does the BLUEPILL NANO use?
The BLUEPILL NANO is built around the BluePill, from the STM32 family.
How big is the BLUEPILL NANO PCB?
The BLUEPILL NANO measures 67.5 × 74.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the BLUEPILL NANO?
27 components, from 12 distinct parts. The full bill of materials is listed on this page.
Where can I download the BLUEPILL NANO design files?
From the KabitaShahu/Circuit repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the BLUEPILL NANO design in my own project?
The repository has no license, so all rights stay with KabitaShahu. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the BLUEPILL NANO without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in Circuit
Microscope
KabitaShahu
133 × 64.1 mm43 parts2LNo license0STM32
BLUEPILL
KabitaShahu
69.5 × 85.9 mm35 parts2LNo license0New pi pico
KabitaShahu
77.5 × 87.5 mm32 parts2LNo license0Pi pico
KabitaShahu
70.8 × 94.1 mm27 parts2LNo license0Numatic optocoupler
KabitaShahu
52 × 55.3 mm24 parts2LNo license0Relay power supply
KabitaShahu
107.7 × 98.8 mm11 parts2LNo license0ESP32
ESP32-wrover
KabitaShahu
37.8 × 111.3 mm9 parts2LNo license0
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k