Dood v1
Karthikpkarthik·Dood_v1·Hardware_files/Dood_v2/Dood_v2.kicad_pcb
About the Dood v1 PCB
Dood v1 is an open source ESP32 PCB design by Karthikpkarthik, published on GitHub. It is a 4-layer board measuring 48.2 × 59 mm, with 22 components from 13 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the LTC4054ES5-4.2 and ADP7142AUJZ-3.3. By type, the board carries 8 capacitors, 4 resistors, 3 ICs, 3 diodes, 1 connector and 1 battery holder.
It belongs with the rf & radio designs in this gallery, and the repository also holds 1 earlier revision of it.
From the project
An offline dog "walkie-talkie" inspired by the Galton whistle. Using a local CNN accelerator for voice recognition, the trainer's node spots commands (like "Sit") and sends a character sequence via Meshtastic LoRa mesh to the dog's collar. The collar's ultrasonic buzzer then emits a specific frequency for silent, remote training.
Main components on the Dood v1
Dood v1 bill of materials (BOM)
22 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 1 | LTC4054ES5-4.2 | TSOT-23-5 | U2 |
| 1 | ADP7142AUJZ-3.3 | TSOT-23-5 | U3 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_HCTL_HC-TYPE-C-16P-01A | J1 |
| 1 | Battery_Cell | LiPO_batt | BT1 |
| 1 | Header_8x2 | PinHeader_2x08_P2.54mm_Vertical | H1 |
| 3 | ESD131-B1-W0201 | D_SOD-923 | D1, D2, D3 |
| 1 | sx1262 | wio-SX1262 | L1 |
| 2 | 0.1uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C3 |
| 6 | 10uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C4, C5, C6, C7, C8 |
| 2 | 5.1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2 |
| 1 | 2kOhms | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | R3 |
| 1 | 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
Dood v1 design files
The KiCad project lives in the Karthikpkarthik/Dood_v1 repository on GitHub; these links point at the commit this page was built from.
Dood v1: common questions
What microcontroller does the Dood v1 use?
The Dood v1 is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the Dood v1 PCB?
The Dood v1 measures 48.2 × 59 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Dood v1?
22 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the Dood v1 design files?
From the Karthikpkarthik/Dood_v1 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Dood v1 design in my own project?
The repository has no license, so all rights stay with Karthikpkarthik. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Dood v1 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Earlier revisions in the repo: Dood_v1
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k