HardLabs

EBoard remote reciever

kattemjau·MountainX-remote·RECIEVER/eBoard_remote_reciever.kicad_pcb

EBoard remote reciever PCB layout, top view — open source Nordic nRF board by kattemjau

About the EBoard remote reciever PCB

EBoard remote reciever is an open source Nordic nRF PCB design by kattemjau, published on GitHub under the MIT license. It is a board measuring 47.5 × 33 mm, with 28 components from 23 distinct parts.

Its main chip is the MDBT42, from the Nordic nRF family. Other key parts include the AP2112(3.3V) and CP2104. By type, the board carries 9 capacitors, 7 connectors, 5 resistors, 3 ICs, 2 diodes and 1 crystal.

It belongs with the iot & wireless, power & battery and usb & debug tools designs in this gallery.

From the project

PCB of remote

https://learn.adafruit.com/bluefruit-nrf52-feather-learning-guide?view=all#downloads

https://www.electric-skateboard.builders/t/simple-3d-printed-nrf-remote-arduino-controlled/28543

Arduino compadible CODE can be found here: https://github.com/Heplaphon/MountainX-Remote

Follow setupguide from Adafruit: https://learn.adafruit.com/bluefruit-nrf52-feather-learning-guide?view=all#arduino-bsp-setup

Main components on the EBoard remote reciever

MDBT42AP2112(3.3V)CP2104

EBoard remote reciever bill of materials (BOM)

28 components, 23 distinct parts.

QtyPartRefs
1
MDBT42
U1
1
AP2112(3.3V)
U2
1
CP2104
U4
1
32.768
X4
1
TEMP SENS
J2
1
PROG
J101
1
VESC_UART
J102
1
PPM
J103
1
RX_Jumper
J104
1
TX_Jumper
J105
1
USB
P1
1
RED
D1
1
BLUE
D2
1
10uH
L2
2
22pF
C1, C2
2
10uF
C3, C7
1
1uF
C4
2
10µF
C6, C8
1
0.1uF
C10
1
10µF
C17
Show 3 more
QtyPartRefs
3
1K
R1, R2, R9
1
100K
R5
1
1k
R10

EBoard remote reciever design files

The KiCad project lives in the kattemjau/MountainX-remote repository on GitHub; these links point at the commit this page was built from.

EBoard remote reciever: common questions

What microcontroller does the EBoard remote reciever use?

The EBoard remote reciever is built around the MDBT42, from the Nordic nRF family.

How big is the EBoard remote reciever PCB?

The EBoard remote reciever measures 47.5 × 33 mm and is 1.6 mm thick.

How many components are on the EBoard remote reciever?

28 components, from 23 distinct parts. The full bill of materials is listed on this page.

Where can I download the EBoard remote reciever design files?

From the kattemjau/MountainX-remote repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the EBoard remote reciever design in my own project?

Yes, under the terms of its MIT license, which kattemjau chose for the repository.

Can I test firmware for the EBoard remote reciever without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Nordic nRF firmware against it before you order a PCB.

More boards in MountainX-remote

Similar boards