BuzzerBox
KavEn06·Wireless-Trivia-Buzzers·PCB/BuzzerBox/BuzzerBox.kicad_pcb
About the BuzzerBox PCB
BuzzerBox is an open source ESP32 PCB design by KavEn06, published on GitHub under the MIT license. It is a 2-layer board measuring 59 × 67.2 mm, with 20 components from 6 distinct parts.
Its main chip is the ESP32_38pin, from the ESP32 family. By type, the board carries 8 resistors, 4 LEDs and 1 IC.
It belongs with the iot & wireless, audio and power & battery designs in this gallery.
From the project
Trivia Buzzers
BuzzerBox bill of materials (BOM)
20 components, 6 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ~ | ESP32_38pin | U1 |
| 2 | Power | SW_PUSH_1P1T_6x3.5mm_H4.3_APEM_MJTP1243 | 5Vin1, 9Vin1 |
| 4 | SPST | SW_PUSH_1P1T_6x3.5mm_H4.3_APEM_MJTP1243 | BuzzerA1, BuzzerB1, BuzzerC1, BuzzerD1 |
| 1 | SPDT | SW_Slide-03_Wuerth-WS-SLTV_10x2.5x6.4_P2.54mm | PoweSwitch1 |
| 4 | ~ | LED_D5.0mm | LEDA1, LEDB1, LEDC1, LEDD1 |
| 8 | 220R | R_0805_2012Metric | R1, R2, R3, R4, R5, R6, R7, R8 |
BuzzerBox design files
The KiCad project lives in the KavEn06/Wireless-Trivia-Buzzers repository on GitHub; these links point at the commit this page was built from.
BuzzerBox: common questions
What microcontroller does the BuzzerBox use?
The BuzzerBox is built around the ESP32_38pin, from the ESP32 family.
How big is the BuzzerBox PCB?
The BuzzerBox measures 59 × 67.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the BuzzerBox?
20 components, from 6 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the BuzzerBox design files?
From the KavEn06/Wireless-Trivia-Buzzers repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the BuzzerBox design in my own project?
Yes, under the terms of its MIT license, which KavEn06 chose for the repository.
Can I test firmware for the BuzzerBox without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Wireless-Trivia-Buzzers
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k