MainBox
KavEn06·Wireless-Trivia-Buzzers·PCB/MainBox/MainBox.kicad_pcb
About the MainBox PCB
MainBox is an open source ESP32 PCB design by KavEn06, published on GitHub under the MIT license. It is a 2-layer board measuring 59 × 67.2 mm, with 9 components from 8 distinct parts.
Its main chip is the ESP32_38pin, from the ESP32 family. By type, the board carries 1 IC and 1 resistor.
It belongs with the iot & wireless, audio and power & battery designs in this gallery.
From the project
Trivia Buzzers
MainBox bill of materials (BOM)
9 components, 8 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ~ | ESP32_38pin | U1 |
| 2 | Power | SW_PUSH_1P1T_6x3.5mm_H4.3_APEM_MJTP1243 | 5Vin1, 9Vin1 |
| 1 | SPST | SW_PUSH_1P1T_6x3.5mm_H4.3_APEM_MJTP1243 | BuzzerB2 |
| 1 | SCSDVG | PinSocket_1x04_P2.54mm_Vertical | LCD1 |
| 1 | LRBCDIGASDGV | MAX98357A | MAX98357A1 |
| 1 | SPDT | SW_Slide-03_Wuerth-WS-SLTV_10x2.5x6.4_P2.54mm | PoweSwitch1 |
| 1 | CSSCMOMIVG | Micro SD Card Module | SD_CARD1 |
| 1 | 220R | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R9 |
MainBox design files
The KiCad project lives in the KavEn06/Wireless-Trivia-Buzzers repository on GitHub; these links point at the commit this page was built from.
MainBox: common questions
What microcontroller does the MainBox use?
The MainBox is built around the ESP32_38pin, from the ESP32 family.
How big is the MainBox PCB?
The MainBox measures 59 × 67.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the MainBox?
9 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the MainBox design files?
From the KavEn06/Wireless-Trivia-Buzzers repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the MainBox design in my own project?
Yes, under the terms of its MIT license, which KavEn06 chose for the repository.
Can I test firmware for the MainBox without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Wireless-Trivia-Buzzers
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k