PrintBridge

Kingdragoncat·PrintBridge·hardware/PrintBridge.kicad_pcb

PrintBridge PCB layout, top view — open source ESP32 board by Kingdragoncat

About the PrintBridge PCB

PrintBridge is an open source ESP32 PCB design by Kingdragoncat, published on GitHub. It is a 2-layer board measuring 92.4 × 40.6 mm, with 18 components from 14 distinct parts.

Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the AMS1117-3.3. By type, the board carries 4 capacitors, 4 resistors, 3 connectors, 2 ICs, 2 switches and 1 fuse.

It belongs with the iot & wireless and usb & debug tools designs in this gallery.

From the project

Im so done with needing to unplug all my cords and plug it all in ontip of a file of boxes to print one god damn thing so i made my wired printer wireless

Im so done with needing to unplug all my cords and plug it all in ontip of a file of boxes to print one god damn thing so i made my wired printer wireless

A small, cheap PCB that turns a wired USB printer into a WiFi network printer. It plugs into the printer's USB port as a USB Host, and exposes it on the network via raw JetDirect (port 9100) printing — works natively with macOS/Windows/Linux print dialogs, no drivers needed on the printer side.

PrintBridge, from the project README
From the project README

Main components on the PrintBridge

PrintBridge bill of materials (BOM)

18 components, 14 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-S3-WROOM-1
U1
1
AMS1117-3.3
Advanced Monolithic Systems
U2
1
Micro_SD_Card
J1
1
TYPE-C-31-M-12
韩国韩荣
J2
1
CONN_01X04
Conn_01x04
J3
1
Polyfuse
F1
2
TS-1187A-B-A-B
XKB Connection(中国星坤)
SW1, SW2
1
A/F90度外扣铜壳鱼叉脚无卷边加高9.3白胶PBT 不耐高温
USB-A-F-90
精拓金
USB1
1
WS2812B
D1
2
100NF
100nF
C1, C3
1
10 uF
C2
1
10UF
10uF
C4
2
10K
10k
R1, R2
2
5.1K
5.1k
R3, R4

PrintBridge design files

The KiCad project lives in the Kingdragoncat/PrintBridge repository on GitHub; these links point at the commit this page was built from.

PrintBridge: common questions

What microcontroller does the PrintBridge use?

The PrintBridge is built around the ESP32-S3-WROOM-1, from the ESP32 family.

How big is the PrintBridge PCB?

The PrintBridge measures 92.4 × 40.6 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the PrintBridge?

18 components, from 14 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the PrintBridge design files?

From the Kingdragoncat/PrintBridge repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the PrintBridge design in my own project?

The repository has no license, so all rights stay with Kingdragoncat. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the PrintBridge without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards