Blare
kira-iovenko·blare·pcb/blare.kicad_pcb
About the Blare PCB
Blare is an open source ESP32 PCB design by kira-iovenko, published on GitHub. It is a 2-layer board measuring 67.2 × 68.2 mm, with 9 components from 4 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. By type, the board carries 6 switches, 1 IC, 1 connector and 1 buzzer.
It belongs with the iot & wireless designs in this gallery.
From the project
A 6-key alarm clock with a wide 2.25" screen and a buzzer that won't let you go back to sleep. To turn the alarm off you have to type a random code. I built the PCB, case and firmware from scratch.
A 6-key alarm clock with a wide 2.25" screen and a buzzer that won't let you go back to sleep. To turn the alarm off you have to type a random code. I built the PCB, case and firmware from scratch.
- Big 7-segment style clock with seconds, the date, and the alarm status - Gets the time from the internet over WiFi (NTP), with automatic daylight saving - The alarm can repeat every day, on weekdays, on weekends, or ring once, and it has a snooze - Stop code: to stop the alarm you type a random key sequence shown on the screen - Night mode dims the digits to red so the clock doesn't light up the…

Main components on the Blare
Blare bill of materials (BOM)
9 components, 4 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C3-DIP-SMD | U1 |
| 1 | Conn_01x08_Pin | PinSocket_1x08_P2.54mm_Vertical | J1 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 6 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2, SW3, SW4, SW5, SW6 |
Blare design files
The KiCad project lives in the kira-iovenko/blare repository on GitHub; these links point at the commit this page was built from.
- Layoutpcb/blare.kicad_pcb
- Schematicpcb/blare.kicad_sch
- BOMBOM.csv
Blare: common questions
What microcontroller does the Blare use?
The Blare is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Blare PCB?
The Blare measures 67.2 × 68.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Blare?
9 components, from 4 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Blare design files?
From the kira-iovenko/blare repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Blare design in my own project?
The repository has no license, so all rights stay with kira-iovenko. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Blare without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k