EBike
klay2000·EBike·EBike CAD/Electrical/Control Board/Ebike Board.kicad_pcb
About the EBike PCB
EBike is an open source ESP32 PCB design by klay2000, published on GitHub. It is a 2-layer board measuring 49.5 × 87.4 mm, with 26 components from 17 distinct parts.
Its main chip is the ESP32-WROOM-32, from the ESP32 family. Other key parts include the TL2575HV-33IKTTR and MCP23S17_SO. By type, the board carries 12 connectors, 4 resistors, 3 capacitors, 2 ICs, 1 module and 1 jumper.
From the project
Software and CAD for my ebike
This repo contains the software and CAD files for my ebike.
All the software is currently written in Arduino and uses a few different libraries.
All the CAD files are made in Fusion 360/KiCAD and are put here in iges format/as a KiCAD project. At the moment my ebike runs a 48 volt 1500w brushless motor running at a maximum of 30 amps. My motor is powered by a FSESC motor controller, which I interface with over UART with a custom ESP32 board. My battery is a 48 volt 13AH li-ion Unit Pack Power battery pack.
Main components on the EBike
EBike bill of materials (BOM)
26 components, 17 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TL2575HV-33IKTTR | TO-263-5_TabPin6 | U1 |
| 1 | MCP23S17_SO | SOIC-28W_7.5x17.9mm_P1.27mm | U3 |
| 1 | ESP32-WROOM-32 | ESP32-WROOM-32D | MOD1 |
| 2 | Conn_01x02_Female | JST_XH_B2B-XH-AM_1x02_P2.50mm_Vertical | J1, J4 |
| 5 | Conn_01x05_Female | JST_XH_B5B-XH-AM_1x05_P2.50mm_Vertical | J2, J8, J9, J10, J11 |
| 3 | Conn_01x04_Female | JST_XH_B4B-XH-AM_1x04_P2.50mm_Vertical | J3, J6, J12 |
| 1 | Conn_01x03_Female | JST_XH_B3B-XH-AM_1x03_P2.50mm_Vertical | J5 |
| 1 | 0022232041 | PinHeader_1x04_P2.54mm_Vertical | J7 |
| 1 | Jumper_NO_Small | PinHeader_1x02_P2.54mm_Vertical | JP1 |
| 1 | SW_Push | SW_PUSH_6mm | SW1 |
| 1 | SR306 | D_DO-201AD_P12.70mm_Horizontal | D1 |
| 1 | 330 uH | L_Radial_D12.5mm_P7.00mm_Fastron_09HCP | L1 |
| 1 | 100uF | CP_Radial_D10.0mm_P5.00mm | C1 |
| 1 | 330uF | CP_Radial_D6.3mm_P2.50mm | C2 |
| 1 | 0.1uf | R_0201_0603Metric | C8 |
| 3 | 65 | R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R1, R2, R3 |
| 1 | 10k | R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R4 |
EBike design files
The KiCad project lives in the klay2000/EBike repository on GitHub; these links point at the commit this page was built from.
EBike: common questions
What microcontroller does the EBike use?
The EBike is built around the ESP32-WROOM-32, from the ESP32 family.
How big is the EBike PCB?
The EBike measures 49.5 × 87.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the EBike?
26 components, from 17 distinct parts. The full bill of materials is listed on this page.
Where can I download the EBike design files?
From the klay2000/EBike repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the EBike design in my own project?
The repository has no license, so all rights stay with klay2000. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the EBike without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k