ProjectCleanbot
Klinsman00·ProjectCleanbot
About the ProjectCleanbot PCB
ProjectCleanbot is an open source ESP32 PCB design by Klinsman00, published on GitHub. It is a board, with 17 components from 13 distinct parts.
Its main chip is the ESP32-S3-DEVKITC-1-N8R8, from the ESP32 family. By type, the board carries 5 connectors, 4 modules, 2 ICs, 2 switches, 1 battery holder and 1 diode.
It belongs with the robotics & motion, iot & wireless and power & battery designs in this gallery.
From the project
Storage for my clean bot project and journals
The reason i decided on making this project is because i thought about my family back in Sabah sweeping and vacuuming the house and want to lessen their burden a little so after making this robot i will be sending it over to them.
Total: RM623.80 / RM820 Forge A-tier cap · 3D printing not included yet (quote pending) - Full list: bom.csv
Main components on the ProjectCleanbot
ProjectCleanbot bill of materials (BOM)
17 components, 13 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-DEVKITC-1-N8R8 | ESP32-S3-DEVKITC-1-N8R8 | U1 |
| 1 | — | U2 | |
| 2 | Gearmotor 298:1 | M1, M3 | |
| 1 | Gearmotor 10:1 | M2 | |
| 1 | Blower motor | M4 | |
| 2 | Ir Sensor (4-30cm) | J1, J3 | |
| 1 | L298N | J2 | |
| 2 | Motor Encoder | J4, J5 | |
| 1 | 12V Battery | BT1 | |
| 1 | — | IRF520MC | |
| 2 | SW_SPDT | SW1, SW2 | |
| 1 | LED 2V | D1 | |
| 1 | 100 Ohm Resistor | R1 |
ProjectCleanbot design files
The KiCad project lives in the Klinsman00/ProjectCleanbot repository on GitHub; these links point at the commit this page was built from.
- Schematicclean_o_bot pcb.kicad_sch
- BOMbom.csv
ProjectCleanbot: common questions
What microcontroller does the ProjectCleanbot use?
The ProjectCleanbot is built around the ESP32-S3-DEVKITC-1-N8R8, from the ESP32 family.
How many components are on the ProjectCleanbot?
17 components, from 13 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the ProjectCleanbot design files?
From the Klinsman00/ProjectCleanbot repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the ProjectCleanbot design in my own project?
The repository has no license, so all rights stay with Klinsman00. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the ProjectCleanbot without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k