Thermistor to linux
kotarou3·thermistor-to-linux·thermistor-to-digispark-pcb/thermistor-to-digispark.kicad_pcb
About the Thermistor to linux PCB
Thermistor to linux is an open source PCB design by kotarou3, published on GitHub. It is a 2-layer board measuring 20 × 22 mm, with 12 components from 7 distinct parts.
Other key parts include the MAX6698 and Digispark. By type, the board carries 8 resistors, 2 ICs, 1 connector and 1 capacitor.
It belongs with the sensors designs in this gallery.
From the project
This project creates three thermistor inputs that can be read via the Linux hwmon interface
This project creates three thermistor inputs that can be read via the Linux hwmon interface
It uses the MAX6698 chip for its 3 thermistor inputs, attached to an I2C-Tiny-USB via I2C, which then attaches onto the system USB bus
I chose the MAX6698 because it was one of the few chips satisfying: - Already has a Linux hwmon driver - Talks I2C/SMBus - Has dedicated thermistor inputs - Available via low MOQ suppliers like Digikey
Main components on the Thermistor to linux
Thermistor to linux bill of materials (BOM)
12 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MAX6698 | TSSOP-16_4.4x5mm_P0.65mm | U1 |
| 1 | Digispark | digispark | U2 |
| 1 | Conn_01x06 | PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | 100nF | C_0603_1608Metric | C1 |
| 2 | 10k | R_0603_1608Metric | R1, R2 |
| 3 | 1.5k | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R3, R4, R5 |
| 3 | 390 | R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R6, R7, R8 |
Thermistor to linux design files
The KiCad project lives in the kotarou3/thermistor-to-linux repository on GitHub; these links point at the commit this page was built from.
Thermistor to linux: common questions
How big is the Thermistor to linux PCB?
The Thermistor to linux measures 20 × 22 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Thermistor to linux?
12 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the Thermistor to linux design files?
From the kotarou3/thermistor-to-linux repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Thermistor to linux design in my own project?
The repository has no license, so all rights stay with kotarou3. Use it as a reference, and ask the author before reusing the design.
Similar boards
Sensor smd
scottbez1
40 × 20 mm5 parts2LApache-2.04.2kSensors
StuckAtPrototype
15.2 × 9 mm14 parts4LApache-2.03.8kMicrophone
Mentra-Community
5.5 × 6.1 mm6 parts2LMIT1.2kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kPots
shanteacontrols
390 × 93 mm75 parts2LApache-2.0956USB
shanteacontrols
52 × 12.6 mm6 parts2LApache-2.0956