Tone-Dial

krishivjoshi219-collab·Tone-Dial·Tone Dial/Tone Dial.kicad_pcb

Tone-Dial PCB layout, top view — open source ESP32 board by krishivjoshi219-collab

About the Tone-Dial PCB

Tone-Dial is an open source ESP32 PCB design by krishivjoshi219-collab, published on GitHub. It is a 2-layer board measuring 96 × 95.1 mm, with 25 components from 18 distinct parts.

Its main chip is the ESP32-S3-DevKit-Left, from the ESP32 family. By type, the board carries 4 switches, 4 diodes, 3 resistors, 2 connectors and 1 capacitor.

It belongs with the audio, iot & wireless and displays & leds designs in this gallery.

From the project

YO WHAT IS UP HACK CLUB REVIWRES AND RAMDOM GITHUB PEOPLE !!!!!!!!! 👋 so basically this is my project for Half-Life Week 3 (Make Some Noise / Music week) and its called TONE DIAL (yes from skypiea in one piece bcuz brook is litterly the GOAT no debate 😤).

YO WHAT IS UP HACK CLUB REVIWRES AND RAMDOM GITHUB PEOPLE !!!!!!!!! 👋 so basically this is my project for Half-Life Week 3 (Make Some Noise / Music week) and its called TONE DIAL (yes from skypiea in one piece bcuz brook is litterly the GOAT no debate 😤).

and like its NOT just a dumb boring speaker or some basic 3 button macropad that just beep boops lol... its a LITTERAL STANDALONE SYNTHESIZER + OPTICAL THEREMIN + USB MIDI CONTROLLER + AI DESK PET COMPANION THINGY THAT ACTUALLY LIVES ON MY DESK !!!!!!! (bruh it took so long to finilaze the idea my brain was melting)

Tone-Dial, from the project README
From the project README

Tone-Dial bill of materials (BOM)

25 components, 18 distinct parts.

QtyPartRefs
1
Conn_01x04_Pin
J1
1
Conn_01x08_Pin
J2
1
MAX98357A
J_AMP1
1
Amp_Speaker_Pads
J_AMP_OUT1
1
JST_PH_2.0mm_LiPo
J_BATT1
1
ESP32-S3-DevKit-Left
J_ESP_LEFT1
1
ESP32-S3-DevKit-Right
J_ESP_RIGHT1
1
INMP441_Module
J_MIC1
1
Speaker_40mm_4R_3W
J_SPK1
1
10k_Slide_Pot
RV_SLIDE1
4
Kailh_Choc_V1
SW1, SW2, SW3, SW4
1
EC11_Encoder
SW_ENC1
1
Slide_Switch_SPDT
SW_PWR1
1
TP4056_5V_Boost_Module
U_PWR1
4
1N4148
D1, D2, D3, D4
1
100uF
C1
1
100k
R1
2
4.7k
R2, R3

Tone-Dial design files

The KiCad project lives in the krishivjoshi219-collab/Tone-Dial repository on GitHub; these links point at the commit this page was built from.

Tone-Dial: common questions

What microcontroller does the Tone-Dial use?

The Tone-Dial is built around the ESP32-S3-DevKit-Left, from the ESP32 family.

How big is the Tone-Dial PCB?

The Tone-Dial measures 96 × 95.1 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Tone-Dial?

25 components, from 18 distinct parts. The full bill of materials is listed on this page.

Where can I download the Tone-Dial design files?

From the krishivjoshi219-collab/Tone-Dial repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Tone-Dial design in my own project?

The repository has no license, so all rights stay with krishivjoshi219-collab. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Tone-Dial without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards