AirHockeyRobot

Lew-Alex·AirHockeyRobot·src/test_pcb/out/kicad/airhockey_breakout.kicad_pcb

AirHockeyRobot PCB layout, top view — open source ESP32 board by Lew-Alex

About the AirHockeyRobot PCB

AirHockeyRobot is an open source ESP32 PCB design by Lew-Alex, published on GitHub. It is a 2-layer board measuring 86 × 64 mm, with 50 components from 22 distinct parts.

Its main chip is the ESP32 DevKitC L, from the ESP32 family. By type, the board carries 13 connectors, 1 jumper and 1 diode.

It belongs with the dev boards & breakouts and robotics & motion designs in this gallery.

From the project

A robotic air-hockey table. A camera tracks the puck, a policy trained in simulation decides where the mallet should go, and an ESP32 drives two brushed DC motors through off-board motor drivers.

A robotic air-hockey table. A camera tracks the puck, a policy trained in simulation decides where the mallet should go, and an ESP32 drives two brushed DC motors through off-board motor drivers.

This is a personal project in progress. The status table below separates what exists in this repository from what is only planned.

The Mac is meant to run perception and the trained policy. The ESP32 handles the low-level motor interface through the breakout PCB. See docs/architecture.md.

AirHockeyRobot bill of materials (BOM)

50 components, 22 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32 DevKitC L
J1
1
ESP32 DevKitC R
J2
1
ENC1
J3
1
ENC2
J4
1
MOTOR1
J5
1
MOTOR2
J6
1
LIM1
J7
1
LIM2
J8
1
LIM3
J9
1
LIM4
J10
1
ESTOP
J11
1
C37208
SPARE
J12
1
DRV_5V
J13
4
100nF
CD_LIM1, CD_LIM2, CD_LIM3, CD_LIM4
2
100NF
100nF
CE1, CE2
4
330pF
CF_E1A, CF_E1B, CF_E2A, CF_E2B
1
C49257
ENC_VCC
JP1
9
1k
RF_E1A, RF_E1B, RF_E2A, RF_E2B, RL1, RS_LIM1, RS_LIM2, RS_LIM3 +1
8
10k
RP_DIR1, RP_DIR2, RP_PWM1, RP_PWM2, RU_LIM1, RU_LIM2, RU_LIM3, RU_LIM4
4
220
RS_DIR1, RS_DIR2, RS_PWM1, RS_PWM2
Show 2 more
QtyPartRefs
4
4.7k
RU_E1A, RU_E1B, RU_E2A, RU_E2B
1
GREEN
D1

AirHockeyRobot design files

The KiCad project lives in the Lew-Alex/AirHockeyRobot repository on GitHub; these links point at the commit this page was built from.

AirHockeyRobot: common questions

What microcontroller does the AirHockeyRobot use?

The AirHockeyRobot is built around the ESP32 DevKitC L, from the ESP32 family.

How big is the AirHockeyRobot PCB?

The AirHockeyRobot measures 86 × 64 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the AirHockeyRobot?

50 components, from 22 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the AirHockeyRobot design files?

From the Lew-Alex/AirHockeyRobot repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the AirHockeyRobot design in my own project?

The repository has no license, so all rights stay with Lew-Alex. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the AirHockeyRobot without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards