RemotePlugSocket
About the RemotePlugSocket PCB
RemotePlugSocket is an open source ESP32 PCB design by Linoprit, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 83.8 × 52.1 mm, with 14 components from 11 distinct parts.
Its main chip is the ESP32-DevKitC, from the ESP32 family. By type, the board carries 7 connectors, 5 resistors, 1 IC and 1 capacitor.
It belongs with the iot & wireless designs in this gallery.
From the project
Plug Socket, that can be controlled by Mqtt-Messages. Especially designed for HomeAssistant.
Main components on the RemotePlugSocket
RemotePlugSocket bill of materials (BOM)
14 components, 11 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-DevKitC | ESP32-DevKitC | U1 |
| 1 | BME280 | Molex_KK-254_AE-6410-04A_1x04_P2.54mm_Vertical | J1 |
| 1 | Relay_Module | Molex_KK-254_AE-6410-06A_1x06_P2.54mm_Vertical | J2 |
| 1 | LED_Status | Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | J3 |
| 1 | 1-Wire CH1 | Molex_KK-254_AE-6410-03A_1x03_P2.54mm_Vertical | J4 |
| 1 | Power | Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | J5 |
| 1 | Button | Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | J6 |
| 1 | LED_Debug | Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | J7 |
| 1 | 470u | CP_Radial_D8.0mm_P3.50mm | C1 |
| 3 | 4.7k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R4 |
| 2 | 330 | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3, R5 |
RemotePlugSocket design files
The KiCad project lives in the Linoprit/RemotePlugSocket repository on GitHub; these links point at the commit this page was built from.
RemotePlugSocket: common questions
What microcontroller does the RemotePlugSocket use?
The RemotePlugSocket is built around the ESP32-DevKitC, from the ESP32 family.
How big is the RemotePlugSocket PCB?
The RemotePlugSocket measures 83.8 × 52.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the RemotePlugSocket?
14 components, from 11 distinct parts. The full bill of materials is listed on this page.
Where can I download the RemotePlugSocket design files?
From the Linoprit/RemotePlugSocket repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the RemotePlugSocket design in my own project?
Yes, under the terms of its GPL-3.0 license, which Linoprit chose for the repository.
Can I test firmware for the RemotePlugSocket without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32Open Book Abridged Edition
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1k
ESP32Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0k
ESP32Esp32 minimal
36.2 × 26.8 mm20 parts2LMIT4.0k
ESP32Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k
ESP32Controller
29 × 74 mm58 parts4LApache-2.03.8k
ESP32Bitaxe
skot
56.5 × 99.8 mm86 parts4LCERN-OHL-S-2.01.4k