Heatpress timer
luteron6·heatpress-timer·PCB/HeatPressTimer.kicad_pcb
About the Heatpress timer PCB
Heatpress timer is an open source ESP32 PCB design by luteron6, published on GitHub under the MIT license. It is a 2-layer board measuring 58 × 35 mm, with 6 components from 5 distinct parts.
Its main chip is the XIAO-ESP32-C6, from the ESP32 family. By type, the board carries 3 switches, 2 connectors and 1 IC.
It belongs with the displays & leds designs in this gallery.
From the project
The repo for my heatpress timer.
There's three main parts: ### The CAD The case! Three parts, the top/bottom of the case, and the vertical switch mount. The /CAD folder has all the parts as a STL, and everything in the STEP file. Meant to be 3D printed.
Main components on the Heatpress timer
Heatpress timer bill of materials (BOM)
6 components, 5 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C6 | XIAO-ESP32C6-DIP | U1 |
| 1 | 2" SPI ST7789VW Display | 8-pin pads | J1 |
| 1 | Piezo | Buzzer | J2 |
| 2 | Switch | 2-pin pads | SW1, SW2 |
| 1 | Vertical Limit Switch | Vertical Switch | SW3 |
Heatpress timer design files
The KiCad project lives in the luteron6/heatpress-timer repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/HeatPressTimer.kicad_pcb
- SchematicPCB/HeatPressTimer.kicad_sch
- BOMBOM.csv
Heatpress timer: common questions
What microcontroller does the Heatpress timer use?
The Heatpress timer is built around the XIAO-ESP32-C6, from the ESP32 family.
How big is the Heatpress timer PCB?
The Heatpress timer measures 58 × 35 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Heatpress timer?
6 components, from 5 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Heatpress timer design files?
From the luteron6/heatpress-timer repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Heatpress timer design in my own project?
Yes, under the terms of its MIT license, which luteron6 chose for the repository.
Can I test firmware for the Heatpress timer without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k