SENTINEL

MartinBugar·SENTINEL·hardware/kicad/sentinel-fc/sentinel-fc.kicad_sch

This repository ships a schematic but no board layout.

About the SENTINEL PCB

SENTINEL is an open source STM32 PCB design by MartinBugar, published on GitHub under the MIT license. It is a board, with 45 components from 28 distinct parts.

Its main chip is the STM32H743VIT6, from the STM32 family. Other key parts include the ICM-42688-P, BMP388, AMS1117-3.3 and MP1584EN. By type, the board carries 18 capacitors, 11 resistors, 8 connectors, 5 ICs, 1 transistor and 1 crystal.

It belongs with the robotics & motion, rf & radio and iot & wireless designs in this gallery.

From the project

Secure Encrypted Network Tactical Intelligence Networked Electronic Liaison

Secure Encrypted Network Tactical Intelligence Networked Electronic Liaison

Open-hardware tactical drone with 100% custom firmware designed for defense-grade applications. No ArduPilot. No Betaflight. Every line of code written from scratch.

- Dual-MCU architecture -- STM32H743 (480 MHz flight controller) + ESP32-S3 (communication module) - AES-256-GCM encrypted communications -- all telemetry and commands authenticated and encrypted - LoRa long-range with frequency hopping -- FHSS anti-jamming on 868 MHz ISM band, 5-10 km range - GPS-denied navigation -- INS fallback via 15-state Extended…

Main components on the SENTINEL

SENTINEL bill of materials (BOM)

45 components, 28 distinct parts.

QtyPartRefs
1
STM32H743VIT6
U1
1
ICM-42688-P
U2
1
BMP388
U3
1
AMS1117-3.3
U4
1
MP1584EN
U5
1
2N7002
Q1
1
25MHz
Y1
1
GPS_BN880
J1
1
SBUS_RC
J2
1
ESC_DShot
J3
1
ESP32_UART
J4
1
SWD_DEBUG
J5
1
WS2812B_LED
J6
1
BUZZER
J7
1
USB-C
J8
1
33uH
L1
2
20pF
C1, C2
10
100nF
C3, C5, C8, C10, C11, C12, C13, C14 +2
3
10uF
C4, C6, C7
1
22uF
C9
Show 8 more
QtyPartRefs
1
4.7uF
C15
1
1uF
C17
1
100K
R1
4
10K
R2, R8, R9, R10
2
4.7K
R3, R4
2
5.1K
R5, R6
1
100R
R7
1
470R
R11

SENTINEL design files

The KiCad project lives in the MartinBugar/SENTINEL repository on GitHub; these links point at the commit this page was built from.

SENTINEL: common questions

What microcontroller does the SENTINEL use?

The SENTINEL is built around the STM32H743VIT6, from the STM32 family.

How many components are on the SENTINEL?

45 components, from 28 distinct parts. The full bill of materials is listed on this page.

Where can I download the SENTINEL design files?

From the MartinBugar/SENTINEL repository on GitHub, which has the schematic; the links under Design files point to each one.

Can I use the SENTINEL design in my own project?

Yes, under the terms of its MIT license, which MartinBugar chose for the repository.

Can I test firmware for the SENTINEL without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards