SpinPOV
maslohaslo1234-spec·SpinPOV·schematic/POV.kicad_sch
About the SpinPOV PCB
SpinPOV is an open source ESP32 PCB design by maslohaslo1234-spec, published on GitHub under the MIT license. It is a board, with 11 components from 11 distinct parts.
Its main chip is the ESP32_30pin, from the ESP32 family. By type, the board carries 5 connectors, 3 capacitors, 1 IC, 1 module and 1 switch.
It belongs with the displays & leds, power & battery and sensors designs in this gallery.
From the project
A persistence-of-vision (POV) display: a spinning arm with 16 APA102 RGB LEDs driven by an ESP32. A Hall sensor and a magnet detect each rotation, so the ESP32 can draw an image in the air. Powered by a removable LiPo battery on the rotor, spun by a small brushed DC motor.
A persistence-of-vision (POV) display. A thin arm with 16 RGB LEDs spins around a motor shaft, and an ESP32 changes the LEDs very fast so that the eye sees a full round image floating in the air. The whole display is screwed to the side of a wardrobe, so it does not need a stand.
Status: design phase (Hack Club Half-Life, week 4, Design with displays). The schematic and the CAD model are done. The build is planned for week 9.
SpinPOV bill of materials (BOM)
11 components, 11 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | — | ESP32_30pin | U1 |
| 1 | Motor_DC | Maple_Mini | M1 |
| 1 | APA102_STRIP | ESP32_30pin | J1 |
| 1 | HALL_A3144 | J2 | |
| 1 | LIPO_1S | J3 | |
| 1 | MT3608_BOOST | ESP32_30pin | J4 |
| 1 | MOTOR_PSU | J5 | |
| 1 | SW_SPST | SW1 | |
| 1 | 470 µF | C1 | |
| 1 | 100 nF | Xilinx_CSG48_7.0x7.0mm_Layout7x7_P0.8mm | C2 |
| 1 | 100 nF | C3 |
SpinPOV design files
The KiCad project lives in the maslohaslo1234-spec/SpinPOV repository on GitHub; these links point at the commit this page was built from.
- Schematicschematic/POV.kicad_sch
SpinPOV: common questions
What microcontroller does the SpinPOV use?
The SpinPOV is built around the ESP32_30pin, from the ESP32 family.
How many components are on the SpinPOV?
11 components, from 11 distinct parts. The full bill of materials is listed on this page.
Where can I download the SpinPOV design files?
From the maslohaslo1234-spec/SpinPOV repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the SpinPOV design in my own project?
Yes, under the terms of its MIT license, which maslohaslo1234-spec chose for the repository.
Can I test firmware for the SpinPOV without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k