SnowHUD Wireless

masonk06·Snowboarding_helmet_goggles·hardware/option-bluetooth-wireless/kicad/SnowHUD_Wireless.kicad_pcb

SnowHUD Wireless PCB layout, top view — open source ESP32 board by masonk06

About the SnowHUD Wireless PCB

SnowHUD Wireless is an open source ESP32 PCB design by masonk06, published on GitHub. It is a 2-layer board measuring 66 × 63.5 mm, with 12 components from 11 distinct parts.

Its main chip is the Seeed XIAO ESP32S3, from the ESP32 family. Other key parts include the ESP32-S3 DevKit (subset of pins), NEO-6M GPS (GY-NEO6MV2), MPU6050 (GY-521) addr 0x68 and BMP280 addr 0x76. By type, the board carries 5 ICs, 2 resistors, 1 connector, 1 switch and 1 capacitor.

It belongs with the iot & wireless, rf & radio and power & battery designs in this gallery.

From the project

In this option the goggles and jacket have no cable between them. Both ends use an ESP32-S3 radio:

In this option the goggles and jacket have no cable between them. Both ends use an ESP32-S3 radio:

- Jacket: the ESP32-S3-DevKitC-1 you already own. It has Bluetooth LE and Wi-Fi built in. - Goggles: the XIAO RP2040, which has no radio, is replaced by a Seeed XIAO ESP32S3. It has the same 14-pin XIAO size and layout, plus a built-in radio and LiPo charger. - The goggles get their own small LiPo battery, on/off switch and battery-voltage monitor.

SnowHUD Wireless, from the project README
From the project README

Main components on the SnowHUD Wireless

Seeed XIAO ESP32S3ESP32-S3 DevKit (subset of pins)NEO-6M GPS (GY-NEO6MV2)MPU6050 (GY-521) addr 0x68BMP280 addr 0x76

SnowHUD Wireless bill of materials (BOM)

12 components, 11 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
Seeed XIAO ESP32S3
U1
1
ESP32-S3 DevKit (subset of pins)
U2
1
NEO-6M GPS (GY-NEO6MV2)
U3
1
MPU6050 (GY-521) addr 0x68
U4
1
BMP280 addr 0x76
U5
1
LiPo 1S 3.7V
J5
1
Waveshare 1.51in OLED (LEFT)
DS1
1
Waveshare 1.51in OLED (RIGHT)
DS2
1
Power ON/OFF
SW1
1
100NF
100nF
C1
2
220K
220k
R1, R2

SnowHUD Wireless design files

The KiCad project lives in the masonk06/Snowboarding_helmet_goggles repository on GitHub; these links point at the commit this page was built from.

SnowHUD Wireless: common questions

What microcontroller does the SnowHUD Wireless use?

The SnowHUD Wireless is built around the Seeed XIAO ESP32S3, from the ESP32 family.

How big is the SnowHUD Wireless PCB?

The SnowHUD Wireless measures 66 × 63.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the SnowHUD Wireless?

12 components, from 11 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the SnowHUD Wireless design files?

From the masonk06/Snowboarding_helmet_goggles repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the SnowHUD Wireless design in my own project?

The repository has no license, so all rights stay with masonk06. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the SnowHUD Wireless without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in Snowboarding_helmet_goggles

Similar boards