Peeler mouse
MaxKiv·peeler_mouse·schematics/cutting-head/kabelPeeler v1.1.kicad_pcb
About the Peeler mouse PCB
Peeler mouse is an open source ESP32 PCB design by MaxKiv, published on GitHub. It is a 2-layer board measuring 40 × 57 mm, with 33 components from 24 distinct parts.
Its main chip is the XIAO-ESP32-S3-DIP, from the ESP32 family. Other key parts include the TMC2209, AMS1117-5.0, ADM3490ExR and AMS1117-3.3. By type, the board carries 11 capacitors, 7 resistors, 6 connectors, 5 ICs, 2 transistors and 2 diodes.
Main components on the Peeler mouse
Peeler mouse bill of materials (BOM)
33 components, 24 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-S3-DIP | XIAO-ESP32-S3-DIP | U1 |
| 1 | TMC2209 | MODULE_TMC2208_SILENTSTEPSTICK | U2 |
| 1 | AMS1117-5.0 | SOT-223-3_TabPin2 | U5 |
| 1 | ADM3490ExR | SOIC-8_3.9x4.9mm_P1.27mm | U6 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U7 |
| 1 | FDV301N | SOT-23_Handsoldering | Q1 |
| 1 | AO3401A | SOT-23 | Q2 |
| 1 | Steppermotor | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J1 |
| 1 | Main input | JST_XH_B6B-XH-A_1x06_P2.50mm_Vertical | J2 |
| 1 | Limit switch | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J3 |
| 1 | Encoder | JST_XH_B6B-XH-A_1x06_P2.50mm_Vertical | J4 |
| 1 | LED-Output | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J5 |
| 1 | Ext Motor VCC | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J6 |
| 2 | LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D2 |
| 1 | 220uF | CP_Radial_D8.0mm_P3.50mm | C1 |
| 4 | 100nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C3, C8, C9 |
| 4 | 10nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4, C5, C6, C7 |
| 2 | 100uF | CP_Radial_D5.0mm_P2.00mm | C10, C11 |
| 1 | 100 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
| 1 | R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3 |
Show 4 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 2.2K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4, R5 |
| 1 | 1K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6 |
| 1 | NC | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7 |
| 1 | 0 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8 |
Peeler mouse design files
The KiCad project lives in the MaxKiv/peeler_mouse repository on GitHub; these links point at the commit this page was built from.
Peeler mouse: common questions
What microcontroller does the Peeler mouse use?
The Peeler mouse is built around the XIAO-ESP32-S3-DIP, from the ESP32 family.
How big is the Peeler mouse PCB?
The Peeler mouse measures 40 × 57 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Peeler mouse?
33 components, from 24 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Peeler mouse design files?
From the MaxKiv/peeler_mouse repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Peeler mouse design in my own project?
The repository has no license, so all rights stay with MaxKiv. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Peeler mouse without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k