66 open source boards using the XIAO-ESP32-S3-DIP

Real designs built with the XIAO-ESP32-S3-DIP, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

66 boardsClear filters|Most starred

How designs wire the XIAO-ESP32-S3-DIP

Read from the KiCad layouts of 37 open source designs, one per repository: what each pin of the XIAO-ESP32-S3-DIP connects to, and the resistors, capacitors and other passives placed on it.

  • The GPIO3/D2/A2 pin has a series resistor on 15 of 37 designs, most often 1 kΩ (then 150 Ω).
GPIO3/D2/A2pin 3Connected to: SN74LVC1G126DBVR 24% · not connected 16%
  • Series resistor on 41% · 1 kΩ (10), 150 Ω (1), 100 Ω (1)
VCC_3V3pin 12Connected to: 3.3V 70% · a signal 16%
GNDpin 13Connected to: GND 95%

11 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Aero-Hand-Open-Left by Chestnut-Robotics, Ledboard by hackclub, Aero-Hand-Open-Left by ss1-ops and Penguin Paddle by Waddle-Penguin.

The XIAO-ESP32-S3-DIP in open source designs

The gallery holds 66 open source boards using the XIAO-ESP32-S3-DIP from 54 GitHub repositories; a typical one measures about 75.6 × 72.8 mm and carries around 23 components.

89% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.

The most starred is Aero-Hand-Open-Left by Chestnut-Robotics.

Microcontrollers on boards using the XIAO-ESP32-S3-DIP

XIAO-ESP32-S3-DIP: common questions

Where can I find a XIAO-ESP32-S3-DIP reference design?

Each of the 66 boards on this page is a real design using the XIAO-ESP32-S3-DIP. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the XIAO-ESP32-S3-DIP GPIO3/D2/A2 pin?

The GPIO3/D2/A2 pin has a series resistor on 15 of 37 designs, most often 1 kΩ (then 150 Ω). Counted from the KiCad layouts of 37 open source designs using the XIAO-ESP32-S3-DIP.

What parts are used alongside the XIAO-ESP32-S3-DIP?

The XIAO-ESP32-C3-DIP, XIAO-ESP32-C3-SMD, XIAO-ESP32-C5-SMD, XIAO-ESP32-C6-DIP and XIAO-ESP32-C6-SMD appear in the most repositories here.

Which microcontrollers do boards using the XIAO-ESP32-S3-DIP use?

Most are built on ESP32 (51), RP2040/RP2350 (14) and Nordic nRF (1).

How big is a typical board using the XIAO-ESP32-S3-DIP?

The median is 75.6 × 72.8 mm, and 89% are two-layer designs.

What is the most popular open source board using the XIAO-ESP32-S3-DIP?

By GitHub stars, Aero-Hand-Open-Left by Chestnut-Robotics, with 1,054 stars.

Can I simulate one of these boards using the XIAO-ESP32-S3-DIP before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part