WearableWLED Hardware
MiCyg·WearableWLED_Hardware
About the WearableWLED Hardware PCB
WearableWLED Hardware is an open source ESP32 PCB design by MiCyg, published on GitHub. It is a 2-layer board measuring 40 × 20 mm, with 20 components from 16 distinct parts.
Its main chip is the ESP32-C3-MINI-1, from the ESP32 family. Other key parts include the MCP73811T-420I-OT. By type, the board carries 8 resistors, 3 capacitors, 2 ICs, 2 connectors, 2 switches and 2 test points.
It belongs with the wearables and power & battery designs in this gallery.
From the project
This PCB combines an ESP32‑C3 Mini with a battery charger, a power switch, and a USB‑C connector for power and programming. All components are low‑cost and readily available. The PCB measures 20×40 mm, allowing a compact enclosure and battery.

Main components on the WearableWLED Hardware
WearableWLED Hardware bill of materials (BOM)
20 components, 16 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-MINI-1 | ESP32-C3-MINI-1 | U1 |
| 1 | MCP73811T-420I-OT | SOT-23-5 | U2 |
| 1 | LED_OUT | PinSocket_1x03_P2.54mm_Vertical | J1 |
| 1 | USB_C_Receptacle_USB2.0_14P | USB_C_Receptacle_G-Switch_GT-USB-7010ASV | P1 |
| 1 | Battery_Cell | Molex_PicoBlade_53047-0210_1x02_P1.25mm_Vertical | BT1 |
| 1 | SWITCH | SW_SPST_CK_RS282G05A3 | SW1 |
| 1 | SW_SPDT | SW_SPDT_Shouhan_MSK12C02 | SW2 |
| 1 | BOOT | SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | TP1 |
| 1 | ENABLE | SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | TP2 |
| 3 | 1u | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C3 |
| 1 | 5.1k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
| 2 | 22 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2, R3 |
| 2 | 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4, R5 |
| 1 | 330k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6 |
| 1 | 560k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7 |
| 1 | 100 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R8 |
WearableWLED Hardware design files
The KiCad project lives in the MiCyg/WearableWLED_Hardware repository on GitHub; these links point at the commit this page was built from.
WearableWLED Hardware: common questions
What microcontroller does the WearableWLED Hardware use?
The WearableWLED Hardware is built around the ESP32-C3-MINI-1, from the ESP32 family.
How big is the WearableWLED Hardware PCB?
The WearableWLED Hardware measures 40 × 20 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the WearableWLED Hardware?
20 components, from 16 distinct parts. The full bill of materials is listed on this page.
Where can I download the WearableWLED Hardware design files?
From the MiCyg/WearableWLED_Hardware repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the WearableWLED Hardware design in my own project?
The repository has no license, so all rights stay with MiCyg. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the WearableWLED Hardware without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k