Remote control
MohamadAminGhanoum·Drone-controller·Remote control/Remote control.kicad_pcb
About the Remote control PCB
Remote control is an open source STM32 PCB design by MohamadAminGhanoum, published on GitHub. It is a 4-layer board measuring 81.1 × 51.6 mm, with 49 components from 30 distinct parts.
Its main chip is the STM32F405RGTx, from the STM32 family. Other key parts include the TPS563200, AP2112K-3.3TRG1 and SX1280IMLTRT. By type, the board carries 25 capacitors, 7 resistors, 4 ICs, 4 connectors, 4 inductors and 2 diodes.
It belongs with the robotics & motion and sensors designs in this gallery.
From the project
So i have this drone that i have had for a very long time. I recieved it without a controller, so it was basically a uselss drone. I played with it previously and tried to connect all 4 motors to 5v to see if it would fly, but ofc it wouldnt stablilize and all that.
Main components on the Remote control
Remote control bill of materials (BOM)
49 components, 30 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F405RGTx | LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | TPS563200 | SOT-23-6 | U5 |
| 1 | AP2112K-3.3TRG1 | SOT95P285X140-5N | U6 |
| 1 | SX1280IMLTRT | XCVR_SX1280IMLTRT | U7 |
| 1 | Crystal_GND24 | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y2 |
| 1 | Left joystick | PinHeader_1x05_P2.54mm_Vertical_SMD_Pin1Left | J2 |
| 1 | Right joystick | PinHeader_1x05_P2.54mm_Vertical_SMD_Pin1Right | J3 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J4 |
| 1 | Battery_connector | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J5 |
| 1 | Antenna | U.FL_Hirose_U.FL-R-SMT-1_Vertical | AE1 |
| 1 | SW_Push | R_0603_1608Metric | SW1 |
| 2 | SS14 | D_SMA | D1, D2 |
| 1 | 3.3uH | L_Bourns_SRP7028A_7.3x6.6mm | L1 |
| 1 | 15uH | L_Bourns_SRP7028A_7.3x6.6mm | L2 |
| 2 | L | L_Bourns_SRP7028A_7.3x6.6mm | L3, L4 |
| 2 | 10uF | C_0603_1608Metric | C1, C2 |
| 11 | 0.1uF | C_0603_1608Metric | C3, C7, C21, C22, C23, C24, C25, C26 +3 |
| 2 | 22uF | C_0603_1608Metric | C4, C6 |
| 1 | 1uF | C_0603_1608Metric | C27 |
| 1 | 2.2uF | C_0603_1608Metric | C28 |
Show 10 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 10nF | C_0603_1608Metric | C31, C33 |
| 1 | 470nF | C_0603_1608Metric | C34 |
| 1 | 0.8pF | C_0603_1608Metric | C35 |
| 2 | 1.2pF | C_0603_1608Metric | C36, C37 |
| 1 | 0.5pF | C_0603_1608Metric | C38 |
| 1 | 100pF | C_0603_1608Metric | C39 |
| 1 | 54.9k | R_0603_1608Metric | R1 |
| 2 | 10k | R_0603_1608Metric | R2, R7 |
| 2 | 5.1k | R_0603_1608Metric | R3, R4 |
| 2 | 22 | R_0603_1608Metric | R5, R6 |
Remote control design files
The KiCad project lives in the MohamadAminGhanoum/Drone-controller repository on GitHub; these links point at the commit this page was built from.
Remote control: common questions
What microcontroller does the Remote control use?
The Remote control is built around the STM32F405RGTx, from the STM32 family.
How big is the Remote control PCB?
The Remote control measures 81.1 × 51.6 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Remote control?
49 components, from 30 distinct parts. The full bill of materials is listed on this page.
Where can I download the Remote control design files?
From the MohamadAminGhanoum/Drone-controller repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Remote control design in my own project?
The repository has no license, so all rights stay with MohamadAminGhanoum. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Remote control without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in Drone-controller
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k