Drone controller project

MohamadAminGhanoum·Drone-controller·Drone controller project/Drone controller project .kicad_pcb

Drone controller project PCB layout, top view — open source STM32 board by MohamadAminGhanoum

About the Drone controller project PCB

Drone controller project is an open source STM32 PCB design by MohamadAminGhanoum, published on GitHub. It is a 4-layer board measuring 69 × 56.5 mm, with 70 components from 37 distinct parts.

Its main chip is the STM32F405RGTx, from the STM32 family. Other key parts include the MPU-6000, DRV8833PWP, TPS563200, AP2112K-3.3TRG1 and SX1280IMLTRT. By type, the board carries 41 capacitors, 7 ICs, 7 resistors, 6 connectors, 4 inductors and 2 diodes.

It belongs with the robotics & motion and sensors designs in this gallery.

From the project

So i have this drone that i have had for a very long time. I recieved it without a controller, so it was basically a uselss drone. I played with it previously and tried to connect all 4 motors to 5v to see if it would fly, but ofc it wouldnt stablilize and all that.

Drone controller project, from the project README
From the project README

Main components on the Drone controller project

Drone controller project bill of materials (BOM)

70 components, 37 distinct parts.

QtyPartRefs
1
STM32F405RGTx
U1
1
MPU-6000
U2
2
DRV8833PWP
U3, U4
1
TPS563200
U5
1
AP2112K-3.3TRG1
U6
1
SX1280IMLTRT
U7
1
52MHz
Y2
1
USB_C_Receptacle_USB2.0_16P
J1
1
Battery_connector
J2
1
MOTOR1
J3
1
MOTOR2
J4
1
MOTOR3
J5
1
MOTOR4
J6
1
Antenna
AE1
1
SW_Push
SW1
2
SS14
D1, D2
1
3.3uH
L1
1
15uH
L2
2
L
L3, L4
4
10uF
C1, C2, C12, C15
Show 17 more
QtyPartRefs
17
0.1uF
C3, C7, C9, C10, C17, C18, C19, C20 +9
3
22uF
C4, C5, C6
1
2.2nF
C8
2
0.01uF
C11, C16
3
2.2uF
C13, C14, C28
1
1uF
C27
2
10nF
C31, C33
1
470nF
C34
1
0.8pF
C35
2
1.2pF
C36, C37
1
0.5pF
C38
1
100pF
C39
2
15pf
C40, C41
1
54.9k
R1
2
10k
R2, R7
2
5.1k
R3, R4
2
22
R5, R6

Drone controller project design files

The KiCad project lives in the MohamadAminGhanoum/Drone-controller repository on GitHub; these links point at the commit this page was built from.

Drone controller project: common questions

What microcontroller does the Drone controller project use?

The Drone controller project is built around the STM32F405RGTx, from the STM32 family.

How big is the Drone controller project PCB?

The Drone controller project measures 69 × 56.5 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Drone controller project?

70 components, from 37 distinct parts. The full bill of materials is listed on this page.

Where can I download the Drone controller project design files?

From the MohamadAminGhanoum/Drone-controller repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Drone controller project design in my own project?

The repository has no license, so all rights stay with MohamadAminGhanoum. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Drone controller project without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

More boards in Drone-controller

Similar boards