USBPowerBlock
monty124·USBPowerBlock·USBPowerBlock/USBPowerBlock.kicad_pcb
About the USBPowerBlock PCB
USBPowerBlock is an open source ESP32 PCB design by monty124, published on GitHub under the CC-BY-NC-4.0 license. It is a 2-layer board measuring 83.5 × 36.3 mm, with 50 components from 17 distinct parts.
Its main chip is the ESP-WROOM-02, from the ESP32 family. Other key parts include the AMS1117-3.3. By type, the board carries 17 resistors, 7 connectors, 6 capacitors, 5 transistors, 5 fuses and 5 jumpers.
It belongs with the iot & wireless designs in this gallery.
From the project
Tasmota controlled USB Switching
So many things are usb powered but can not or are not able to be integrated easily within Home Assistant; or programable.
Want to turn something on or off automatically? you will need to buy something else! and it still needs a power source
Want it to be integrated into Home Assistant and or control its privacy? good luck off the shelf, you may need to flash it (if its supported)

Main components on the USBPowerBlock
USBPowerBlock bill of materials (BOM)
50 components, 17 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP-WROOM-02 | ESP-WROOM-02-Flexy | U1 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U2 |
| 5 | LMAK15N10 | TO-252-2 | Q1, Q2, Q3, Q4, Q5 |
| 5 | USB_A | USB_11_Aliexpress | J1, J2, J3, J4, J5 |
| 1 | IO | PinHeader_1x05_P1.27mm_Vertical | J6 |
| 1 | Power_In | JST_B2B-XH-A | J7 |
| 5 | JK-SMD0805-020-30V | Fuse_0805_2012Metric_Pad1.15x1.40mm_HandSolder | F1, F2, F3, F4, F5 |
| 5 | ~ | SMT-JUMPER_2_NO_SILK | JP1, JP2, JP3, JP4, JP5 |
| 1 | Blue | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 1 | Green | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2 |
| 1 | Red | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D3 |
| 4 | 0.1UF-0805-25V-_+80_-20%_ | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C3, C4, C6 |
| 2 | 10UF-0805-16V-10% | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C5 |
| 9 | 10KOHM-0805-1_10W-1% | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R3, R4, R5, R7, R9, R11, R15 +1 |
| 5 | 100R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R6, R8, R10, R12 |
| 2 | 68OHM-0805-1_10W-1% | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R13, R17 |
| 1 | 470OHM-0805-1_10W-1% | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R14 |
USBPowerBlock design files
The KiCad project lives in the monty124/USBPowerBlock repository on GitHub; these links point at the commit this page was built from.
USBPowerBlock: common questions
What microcontroller does the USBPowerBlock use?
The USBPowerBlock is built around the ESP-WROOM-02, from the ESP32 family.
How big is the USBPowerBlock PCB?
The USBPowerBlock measures 83.5 × 36.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the USBPowerBlock?
50 components, from 17 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the USBPowerBlock design files?
From the monty124/USBPowerBlock repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the USBPowerBlock design in my own project?
It is published under CC-BY-NC-4.0, which limits how it may be reused; read the license before building on it.
Can I test firmware for the USBPowerBlock without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k