20 open source boards using the ESP-WROOM-02
Real designs built with the ESP-WROOM-02, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Z2m partner
smarthomefans
50 × 50 mm50 parts2LNo license187ESP32
Wifistepper
goodrobotics
77.6 × 57.3 mm85 parts4LNo license29ESP32
Wi-Se ESP8266 - Raspberry Pi style header version
depau
21.6 × 20 mm40 parts4LCERN-OHL-S-2.011ESP32
30a water heater controller
flaviut
85 × 56 mm42 parts2LCERN-OHL-S-2.02ESP32
Lkf 4-button insert (front
slimcdk
36.2 × 40.6 mm25 parts2LNo license2ESP32
Esp8266-temp proto
ShawnHymel
35.6 × 50.8 mm26 parts2LNo license1ESP32
Smart-Home-Automation-Controller
dhanush-darpan
168 × 61 mm68 parts2LNo license0ESP32
Esp bluepill board
ar216-2355
84.7 × 75.8 mm67 parts2LNo license0ESP32
ESXAR panelize
nanbuwks
31.8 × 22.9 mm51 parts2LUnlicense0ESP32
Window sensor
physiii
83.5 × 48.5 mm51 parts2LNo license0ESP32
USBPowerBlock
monty124
83.5 × 36.3 mm50 parts2LCC-BY-NC-4.00ESP32
Garage opener
physiii
83.5 × 48.5 mm46 parts2LNo license0ESP32
Calender
hardwarepro
94 × 27.5 mm44 parts2LNo license0ESP32
Slime2
ntxngle
30.9 × 19.6 mm25 parts4LNo license0ESP32
Wi se opi4
depau
20.1 × 26.5 mm33 parts4LCERN-OHL-S-2.011ESP32
CO2 SENSOR
odobot
20 × 73.4 mm44 parts4LNo license1ESP32
ESXAR
nanbuwks
62.9 × 60.8 mm46 parts2LUnlicense0ESP32
Wi se rewirable
depau
25.6 × 22.4 mm33 parts4LCERN-OHL-S-2.011ESP32
Esp wroom-2-carrier board
cpeniche
33.8 × 34.4 mm31 parts4LNo license0ESP32
ESP-WROOM-02 Breakout
vul-os
27.9 × 25.4 mm4 parts2LApache-2.055
How designs wire the ESP-WROOM-02
Read from the KiCad layouts of 17 open source designs, one per repository: what each pin of the ESP-WROOM-02 connects to, and the resistors, capacitors and other passives placed on it.
- The EN pin has a pull-up to 3.3V on 11 of 17 designs, most often 10 kΩ.
- The IO15 pin has a resistor to GND on 9 of 17 designs, most often 10 kΩ (then 1 kΩ).
- The IO2 pin has a pull-up to 3.3V on 8 of 17 designs, most often 10 kΩ (then 2.2 kΩ).
- The VDD pin has a decoupling capacitor on 7 of 17 designs, most often 100 nF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDpin 1 | Connected to: 3.3V 94% |
|
| ENpin 2 | Connected to: Signal 100% |
|
| IO15pin 6 | Connected to: A connector 24% |
|
| IO2pin 7 | Connected to: A connector 24% · not connected 24% |
|
| IO0pin 8 | Connected to: A connector 41% |
|
| GNDpin 9, 13, 18, 19 | Connected to: GND 97% | — |
10 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Z2m partner by smarthomefans, ESP-WROOM-02 Breakout by vul-os, Wifistepper by goodrobotics and Wi se opi4 by depau.
The ESP-WROOM-02 in open source designs
The gallery holds 20 open source boards using the ESP-WROOM-02 from 17 GitHub repositories; a typical one measures about 43.1 × 44.5 mm and carries around 44 components.
65% are two-layer designs, the rest use four layers or more, and 35% carry an open source license.
The most starred is Z2m partner by smarthomefans.
Parts used alongside the ESP-WROOM-02
Microcontrollers on boards using the ESP-WROOM-02
What boards using the ESP-WROOM-02 are built for
ESP-WROOM-02: common questions
Where can I find a ESP-WROOM-02 reference design?
Each of the 20 boards on this page is a real design using the ESP-WROOM-02. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the ESP-WROOM-02 EN pin?
The EN pin has a pull-up to 3.3V on 11 of 17 designs, most often 10 kΩ. Counted from the KiCad layouts of 17 open source designs using the ESP-WROOM-02.
What resistor goes on the ESP-WROOM-02 IO15 pin?
The IO15 pin has a resistor to GND on 9 of 17 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 17 open source designs using the ESP-WROOM-02.
What pull-up resistor is used on the ESP-WROOM-02 IO2 pin?
The IO2 pin has a pull-up to 3.3V on 8 of 17 designs, most often 10 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 17 open source designs using the ESP-WROOM-02.
Which microcontrollers do boards using the ESP-WROOM-02 use?
Most are built on ESP32 (20).
How big is a typical board using the ESP-WROOM-02?
The median is 43.1 × 44.5 mm, and 65% are two-layer designs.
What is the most popular open source board using the ESP-WROOM-02?
By GitHub stars, Z2m partner by smarthomefans, with 187 stars.
Can I simulate one of these boards using the ESP-WROOM-02 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.