Dewcontroller hardware
mpinnuck·dewcontroller-hardware·hardware/dewcontroller/dewcontroller.kicad_pcb
About the Dewcontroller hardware PCB
Dewcontroller hardware is an open source ESP32 PCB design by mpinnuck, published on GitHub. It is a 2-layer board measuring 72.3 × 64.5 mm, with 15 components from 14 distinct parts.
Its main chip is the XIAO-ESP32-S3-DIP, from the ESP32 family. By type, the board carries 3 ICs, 3 connectors, 3 capacitors, 3 resistors, 2 diodes and 1 transistor.
It belongs with the sensors and iot & wireless designs in this gallery.
From the project
Environment-driven dew heater controller for the Celestron C9.25 corrector plate dew ring.
Environment-driven dew heater controller for the Celestron C9.25 corrector plate dew ring.
This project uses an ESP32-S3 (Seeed XIAO ESP32S3), an SHT40 temperature/humidity sensor, and a PWM-controlled heater channel to reduce dew risk while limiting unnecessary heat.
- Computes dew point from ambient temperature and relative humidity. - Uses spread control: spread = Ta - Td. - Looks up heater output from a configurable spread-to-power table. - Applies a global maximum power cap for safety. - Uses ring thermistor only as an over-temperature safety clamp. - Hosts a built-in web UI for…
Main components on the Dewcontroller hardware
Dewcontroller hardware bill of materials (BOM)
15 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-S3-DIP | MCU_Seeed_ESP32C3_EdgeOnly | U1 |
| 1 | ~ | AHT20 | U2 |
| 1 | ~ | Converter TS-P312 DC Buck | U3 |
| 1 | FQP 30N06L | TO-220-3_Vertical | Q1 |
| 1 | 12V Power Supply | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J1 |
| 1 | Dew Heater 12V | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J2 |
| 1 | Temperature Sensor | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J3 |
| 1 | 1N5819 | D_DO-41_SOD81_P7.62mm_Horizontal | D1 |
| 1 | 1N4734 | D_DO-41_SOD81_P7.62mm_Horizontal | D2 |
| 1 | 220uf 25V | CP_Radial_D5.0mm_P2.00mm | C1 |
| 1 | 0.01uf | C_Disc_D3.0mm_W1.6mm_P2.50mm | C2 |
| 1 | 100uf | CP_Radial_D5.0mm_P2.00mm | C3 |
| 1 | 330 | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1 |
| 2 | 10K | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2, R3 |
Dewcontroller hardware design files
The KiCad project lives in the mpinnuck/dewcontroller-hardware repository on GitHub; these links point at the commit this page was built from.
Dewcontroller hardware: common questions
What microcontroller does the Dewcontroller hardware use?
The Dewcontroller hardware is built around the XIAO-ESP32-S3-DIP, from the ESP32 family.
How big is the Dewcontroller hardware PCB?
The Dewcontroller hardware measures 72.3 × 64.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Dewcontroller hardware?
15 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the Dewcontroller hardware design files?
From the mpinnuck/dewcontroller-hardware repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Dewcontroller hardware design in my own project?
The repository has no license, so all rights stay with mpinnuck. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Dewcontroller hardware without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k