Buddy
nadellasripad11·buddy·hardware/buddy-robot.kicad_sch
About the Buddy PCB
Buddy is an open source ESP32 PCB design by nadellasripad11, published on GitHub. It is a board, with 30 components from 22 distinct parts.
Its main chip is the ESP32-S3-DEVKITC-1, from the ESP32 family. By type, the board carries 9 connectors, 8 resistors, 6 capacitors, 4 switches, 1 IC and 1 fuse.
It belongs with the robotics & motion designs in this gallery.
From the project
a little desk robot. eventually it should move around, listen, talk back, and feel like it has a personality.
- buddy.kicadsch — schematic - buddy.kicadpcb — board layout - exports/ — gerbers and the bom when the board is ready to order
Main components on the Buddy
Buddy bill of materials (BOM)
30 components, 22 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-DEVKITC-1 | ESP32-S3-DEVKITC-1 | U1 |
| 1 | MAX98357A | PinHeader_1x07_P2.54_Vertical | J1 |
| 1 | VL53L0X | PinHeader_1x04_P2.54_Vertical | J2 |
| 1 | DISPLAY | PinHeader_1x08_P2.54_Vertical | J3 |
| 1 | DRV8833 | PinHeader_2x09_P2.54_Vertical | J4 |
| 1 | EXPANSION | PinHeader_1x08_P2.54_Vertical | J5 |
| 1 | SPEAKER | PinHeader_1x02_P2.54_Vertical | J6 |
| 1 | MOTOR_L | PinHeader_1x02_P2.54_Vertical | J7 |
| 1 | MOTOR_R | PinHeader_1x02_P2.54_Vertical | J8 |
| 1 | USB_IN | PinHeader_1x02_P2.54_Vertical | J9 |
| 1 | PTC_2A | Fuse_2920_7351Metric | F1 |
| 3 | TACT | SW_Push_1P1T_NO_SMD_6x6x4.3mm | SW1, SW2, SW3 |
| 1 | ROCKER | SW_Rocker_SPST | SW4 |
| 1 | RGB_CC | LED_RGB_5050-4 | D1 |
| 1 | 1000u | CP_Radial_D10.0mm_P5.00mm | C1 |
| 1 | 220u | CP_Radial_D10.0mm_P5.00mm | C2 |
| 4 | 100n | C_0805_2012Metric | C3, C4, C5, C6 |
| 1 | 150 | R_0805_2012Metric | R1 |
| 1 | 100 | R_0805_2012Metric | R2 |
| 1 | 33 | R_0805_2012Metric | R3 |
Show 2 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | 10k | R_0805_2012Metric | R4, R5, R6 |
| 2 | 4.7k | R_0805_2012Metric | R7, R8 |
Buddy design files
The KiCad project lives in the nadellasripad11/buddy repository on GitHub; these links point at the commit this page was built from.
Buddy: common questions
What microcontroller does the Buddy use?
The Buddy is built around the ESP32-S3-DEVKITC-1, from the ESP32 family.
How many components are on the Buddy?
30 components, from 22 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Buddy design files?
From the nadellasripad11/buddy repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the Buddy design in my own project?
The repository has no license, so all rights stay with nadellasripad11. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Buddy without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k