Midi-Run
naran-579·Midi-Run·CAD/KiCAD/MiDi RUN.kicad_pcb
About the Midi-Run PCB
Midi-Run is an open source ESP32 PCB design by naran-579, published on GitHub. It is a 2-layer board measuring 111.5 × 73.5 mm, with 12 components from 7 distinct parts.
Its main chip is the Waveshare ESP32-S3-ZERO, from the ESP32 family. By type, the board carries 4 switches, 4 diodes, 1 IC and 1 connector.
It belongs with the audio designs in this gallery.
From the project
Just a project
I would've added more but I ran out of IO
Main components on the Midi-Run
Midi-Run bill of materials (BOM)
12 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Waveshare ESP32-S3-ZERO | Waveshare ESP32-S3-Zero | U1 |
| 1 | Conn_01x07 | Untitled | J1 |
| 2 | R_Potentiometer_MountingPin | Potentiometer_Bourns_PTA1543_Single_Slide | RV1, RV2 |
| 3 | SW_Push | Kailh Choc Low-Profile Switches | SW1, SW2, SW3 |
| 1 | RotaryEncoder_Switch_MP | RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | SW4 |
| 3 | SK6812MINI-E | LED_SK6812MINI-E_3.2x2.8mm_P1.5mm_ReverseMount | D1, D2, D3 |
| 1 | LED | Untitled_1 | D4 |
Midi-Run design files
The KiCad project lives in the naran-579/Midi-Run repository on GitHub; these links point at the commit this page was built from.
- LayoutCAD/KiCAD/MiDi RUN.kicad_pcb
- SchematicCAD/KiCAD/MiDi RUN.kicad_sch
Midi-Run: common questions
What microcontroller does the Midi-Run use?
The Midi-Run is built around the Waveshare ESP32-S3-ZERO, from the ESP32 family.
How big is the Midi-Run PCB?
The Midi-Run measures 111.5 × 73.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Midi-Run?
12 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the Midi-Run design files?
From the naran-579/Midi-Run repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Midi-Run design in my own project?
The repository has no license, so all rights stay with naran-579. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Midi-Run without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k