CircuitBrains Basic v1 2
neubauek·CircuitBrains·CircuitBrains Basic/v1_2/CircuitBrains Basic v1_2/CircuitBrains Basic v1_2.kicad_pcb
About the CircuitBrains Basic v1 2 PCB
CircuitBrains Basic v1 2 is an open source Microchip SAM PCB design by neubauek, published on GitHub under the MIT license. It is a 2-layer board measuring 25 × 25 mm, with 23 components from 14 distinct parts.
Its main chip is the ATSAMD21E18A-MU, from the Microchip SAM family. Other key parts include the W25Q32JVZPIQ, AP2112K-3.3 and 28SOM. By type, the board carries 9 capacitors, 7 resistors, 4 ICs, 2 LEDs and 1 switch.
From the project
Small form-factor 48-pin castellated pad module. Designed to allow an easy implementation of CircuitPython in maker/hacker projects without the bulk of a large breakout board.
Small form-factor 48-pin castellated pad module. Designed to allow an easy implementation of CircuitPython in maker/hacker projects without the bulk of a large breakout board.
Specs: - Atmel ATSAMD51J19A Microcontroller (32-bit ARM Cortex M4) - 8 MB SPI Flash - Onboard 3.3V LDO Regulator - Power and Status LEDs - Breakouts for SPI and I2C - Breakouts for 13 Analog and 19 Digital Inputs/Outputs

Main components on the CircuitBrains Basic v1 2
CircuitBrains Basic v1 2 bill of materials (BOM)
23 components, 14 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | W25Q32JVZPIQ Winbond Electronics | WSON-8-1EP_6x5mm_P1.27mm_EP3.4x4.3mm | U1 |
| 1 | AP2112K-3.3 Diodes Incorporated | SOT-23-5 | U2 |
| 1 | ATSAMD21E18A-MU Microchip Technology | QFN50P500X500X100-33N | U3 |
| 1 | 28SOM | 28SOM_25MMx25MM | U4 |
| 1 | KMR231 C&K | KMR231 | SW1 |
| 1 | GREEN Würth Elektronik | LED_0603_1608Metric | LED1 |
| 1 | RED Würth Elektronik | LED_0603_1608Metric | LED2 |
| 3 | 1UF 1uF Yageo | C_0603_1608Metric | C1, C4, C7 |
| 4 | 0.1UF 0.1uF Yageo | C_0603_1608Metric | C2, C3, C5, C6 |
| 2 | 10UF 10uF Murata | C_0603_1608Metric | C8, C9 |
| 1 | 100K Yageo | R_0603_1608Metric | R1 |
| 1 | 330 Yageo | R_0603_1608Metric | R3 |
| 2 | 10K Yageo | R_0603_1608Metric | R4, R6 |
| 3 | 1K Yageo | R_0603_1608Metric | R5, R7, R8 |
CircuitBrains Basic v1 2 design files
The KiCad project lives in the neubauek/CircuitBrains repository on GitHub; these links point at the commit this page was built from.
CircuitBrains Basic v1 2: common questions
What microcontroller does the CircuitBrains Basic v1 2 use?
The CircuitBrains Basic v1 2 is built around the ATSAMD21E18A-MU, from the Microchip SAM family.
How big is the CircuitBrains Basic v1 2 PCB?
The CircuitBrains Basic v1 2 measures 25 × 25 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the CircuitBrains Basic v1 2?
23 components, from 14 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the CircuitBrains Basic v1 2 design files?
From the neubauek/CircuitBrains repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the CircuitBrains Basic v1 2 design in my own project?
Yes, under the terms of its MIT license, which neubauek chose for the repository.
Can I test firmware for the CircuitBrains Basic v1 2 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Microchip SAM firmware against it before you order a PCB.
More boards in CircuitBrains
Similar boards
Microchip SAM
Microcontroller Expansion Card
FrameworkComputer
26 × 30 mm24 parts2LCC-BY-4.01.1kMicrochip SAM
Taco Raven
VoronDesign
120 × 113 mm349 parts4LGPL-3.01.1kMicrochip SAM
Fpgaboy
Wren6991
50 × 50 mm89 parts4LNo license511Microchip SAM
OpenDropV4
GaudiLabs
124 × 115.4 mm118 parts2LGPL-3.0487Microchip SAM
ModulAdapter universal
GaudiLabs
100 × 69.5 mm45 parts2LGPL-3.0487Microchip SAM
Kira
kiibohd
366.9 × 114.3 mm400 partsCERN-OHL-1.2416