Hub75 esp32s3 controller

neusse·konnect-codex·test-projects/hub75_esp32s3_controller.kicad_pcb

This repository ships a schematic but no board layout.

About the Hub75 esp32s3 controller PCB

Hub75 esp32s3 controller is an open source ESP32 PCB design by neusse, published on GitHub under the AGPL-3.0 license. It is a 2-layer board, with 25 components from 25 distinct parts.

Its main chip is the 3.3V regulator for ESP32, from the ESP32 family. Other key parts include the 3A USB eFuse / load switch, ESP32-S3-WROOM-N16R8 PSRAM, 74AHCT245 color/data level shifter and 74AHCT245 address/control level shifter. By type, the board carries 7 capacitors, 6 switches, 5 ICs, 4 resistors and 3 connectors.

From the project

konnect-codex is a standalone Codex plugin for the Konnect server. It packages reviewed Codex-native skills, agents, hooks, and MCP configuration so Konnect behaves like a first-class Codex integration. It is deliberately separate from Konnect so each release can preserve a known

konnect-codex is a standalone Codex plugin for the Konnect server. It packages reviewed Codex-native skills, agents, hooks, and MCP configuration so Konnect behaves like a first-class Codex integration. It is deliberately separate from Konnect so each release can preserve a known-good Codex workflow without changing Konnect itself.

Release numbers identify the Konnect release reviewed by the plugin: konnect-codex v0.12.1 supports Konnect v0.12.1. A later -codex.N suffix identifies a companion-only revision for that unchanged upstream release. The exact reviewed upstream commit and guidance…

Main components on the Hub75 esp32s3 controller

3A USB eFuse / load switch3.3V regulator for ESP32ESP32-S3-WROOM-N16R8 PSRAM74AHCT245 color/data level shifter74AHCT245 address/control level shifter

Hub75 esp32s3 controller bill of materials (BOM)

25 components, 25 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
3A USB eFuse / load switch
U1
1
3.3V regulator for ESP32
U2
1
ESP32-S3-WROOM-N16R8 PSRAM
U3
1
74AHCT245 color/data level shifter
U4
1
74AHCT245 address/control level shifter
U5
1
USB-C PWR+PROG 5V/3A
J1
1
5V panel power output, >=3A
J2
1
HUB75 2x8 IDC signal output
J3
1
RESET
SW1
1
BOOT/PROGRAM
SW2
1
UP
SW3
1
DOWN
SW4
1
SELECT
SW5
1
BACK
SW6
1
1000uF 6.3V low-ESR bulk
C1
1
22uF 5V input
C2
1
10uF 3V3 output
C3
1
100nF ESP32 decoupling
C4
1
10uF ESP32 bulk
C5
1
100nF U4 decoupling
C6
Show 5 more
QtyPartRefs
1
100nF U5 decoupling
C7
1
5.1k CC1 Rd
R1
1
5.1k CC2 Rd
R2
1
10k EN pull-up
R3
1
10k BOOT pull-up
R4

Hub75 esp32s3 controller design files

The KiCad project lives in the neusse/konnect-codex repository on GitHub; these links point at the commit this page was built from.

Hub75 esp32s3 controller: common questions

What microcontroller does the Hub75 esp32s3 controller use?

The Hub75 esp32s3 controller is built around the 3.3V regulator for ESP32, from the ESP32 family.

How big is the Hub75 esp32s3 controller PCB?

The Hub75 esp32s3 controller has 2 copper layers and is 1.6 mm thick.

How many components are on the Hub75 esp32s3 controller?

25 components, from 25 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Hub75 esp32s3 controller design files?

From the neusse/konnect-codex repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Hub75 esp32s3 controller design in my own project?

Yes, under the terms of its AGPL-3.0 license, which neusse chose for the repository.

Can I test firmware for the Hub75 esp32s3 controller without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in konnect-codex

Similar boards