Pocket watch
Nitish5196·Pocket-watch·watch pcb/watch pcb.kicad_pcb
About the Pocket watch PCB
Pocket watch is an open source ESP32 PCB design by Nitish5196, published on GitHub. It is a 2-layer board measuring 44 × 44 mm, with 10 components from 10 distinct parts.
Its main chip is the XIAO-ESP32-C6-SMD, from the ESP32 family. By type, the board carries 5 connectors, 1 IC, 1 transistor, 1 switch, 1 diode and 1 resistor.
It belongs with the iot & wireless, wearables and power & battery designs in this gallery.
Main components on the Pocket watch
Pocket watch bill of materials (BOM)
10 components, 10 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C6-SMD | XIAO-ESP32-C6-SMD | U1 |
| 1 | 2N2222 | TO-92_Inline | Q1 |
| 1 | DISPLAY | PinHeader_1x07_P2.54mm_Vertical | J1 |
| 1 | BATTERY | PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | WIRELESS_RECEIVER | PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | VIBRATING MOTOR | PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | ACCELEROMETER | PinHeader_1x05_P2.54mm_Vertical | J5 |
| 1 | POWER SWITCH | SW_DPDT_CK_JS202011JCQN | SW1 |
| 1 | 1N4148 | D_DO-35_SOD27_P7.62mm_Horizontal | D1 |
| 1 | 1K | R_0805_2012Metric | R1 |
Pocket watch design files
The KiCad project lives in the Nitish5196/Pocket-watch repository on GitHub; these links point at the commit this page was built from.
Pocket watch: common questions
What microcontroller does the Pocket watch use?
The Pocket watch is built around the XIAO-ESP32-C6-SMD, from the ESP32 family.
How big is the Pocket watch PCB?
The Pocket watch measures 44 × 44 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Pocket watch?
10 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Pocket watch design files?
From the Nitish5196/Pocket-watch repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Pocket watch design in my own project?
The repository has no license, so all rights stay with Nitish5196. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Pocket watch without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k