ESP32 MOTOR KIT PRINT
About the ESP32 MOTOR KIT PRINT PCB
ESP32 MOTOR KIT PRINT is an open source ESP32 PCB design by odobot, published on GitHub. It is a 2-layer board measuring 66 × 60 mm, with 12 components from 12 distinct parts.
Its main chip is the ESP-WROOM-32_USBC, from the ESP32 family. Other key parts include the LM2596S. By type, the board carries 7 connectors, 2 diodes, 1 IC, 1 switch and 1 resistor.
Main components on the ESP32 MOTOR KIT PRINT
ESP32 MOTOR KIT PRINT bill of materials (BOM)
12 components, 12 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM2596S | LM2596 | U1 |
| 1 | Conn_01x04_Male | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J1 |
| 1 | Conn_01x16_Male | PinHeader_1x16_P2.54mm_Vertical | J2 |
| 1 | ESP-WROOM-32_USBC | ESP-WROOM-32 TYPE C | J3 |
| 1 | Conn_02x12_Odd_Even | PinHeader_2x12_P2.54mm_Vertical | J4 |
| 1 | Screw_Terminal_01x02 | TerminalBlock_Phoenix_PT-1,5-2-3.5-H_1x02_P3.50mm_Horizontal | J6 |
| 1 | Conn_01x15_Male | PinHeader_1x15_P2.54mm_Vertical | J7 |
| 1 | Barrel_Jack_Switch | BarrelJack_Wuerth_6941xx301002 | J8 |
| 1 | SW_DIP_x01 | SW_E-Switch_EG1224_SPDT_Angled | SW1 |
| 1 | LED_RGBK | LED_D5.0mm-4_RGB | D1 |
| 1 | LED | LED_D3.0mm | D2 |
| 1 | 1130 | R_Axial_DIN0204_L3.6mm_D1.6mm_P1.90mm_Vertical | R1 |
ESP32 MOTOR KIT PRINT design files
The KiCad project lives in the odobot/PCB_DESIGN repository on GitHub; these links point at the commit this page was built from.
ESP32 MOTOR KIT PRINT: common questions
What microcontroller does the ESP32 MOTOR KIT PRINT use?
The ESP32 MOTOR KIT PRINT is built around the ESP-WROOM-32_USBC, from the ESP32 family.
How big is the ESP32 MOTOR KIT PRINT PCB?
The ESP32 MOTOR KIT PRINT measures 66 × 60 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ESP32 MOTOR KIT PRINT?
12 components, from 12 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the ESP32 MOTOR KIT PRINT design files?
From the odobot/PCB_DESIGN repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the ESP32 MOTOR KIT PRINT design in my own project?
The repository has no license, so all rights stay with odobot. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the ESP32 MOTOR KIT PRINT without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in PCB_DESIGN
AVR/ArduinoBL Ctrl V2
40 × 20 mm85 parts4LNo license1
ESP32CO2 SENSOR
20 × 73.4 mm44 parts4LNo license1
AVR/ArduinoArduino
43.3 × 50 mm41 parts4LNo license1
AVR/ArduinoPcb1
93.1 × 79.3 mm34 parts2LNo license1
AVR/ArduinoAtmega32 Robot
75.9 × 67.9 mm28 parts2LNo license1
IR Array
91 × 22.2 mm21 parts2LNo license1
IR Array(THT)
90 × 26.1 mm15 parts2LNo license1
Similar boards
ESP32Open Book Abridged Edition
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1k
ESP32Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0k
ESP32Esp32 minimal
36.2 × 26.8 mm20 parts2LMIT4.0k
ESP32Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k
ESP32Controller
29 × 74 mm58 parts4LApache-2.03.8k
ESP32Bitaxe
skot
56.5 × 99.8 mm86 parts4LCERN-OHL-S-2.01.4k