Prezenter
onismond·Prezenter
About the Prezenter PCB
Prezenter is an open source ESP32 PCB design by onismond, published on GitHub. It is a 2-layer board measuring 38.1 × 69.9 mm, with 13 components from 11 distinct parts.
Its main chip is the DW01A, from the ESP32 family. By type, the board carries 5 resistors, 3 connectors, 3 switches, 1 IC and 1 diode.
Main components on the Prezenter
Prezenter bill of materials (BOM)
13 components, 11 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DW01A ESP32-WROOM-32 | ESP32-WROOM-32 | U1 |
| 1 | TYPE-C-31-M-17 Laser | PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | Prog | PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | Vin | PinHeader_1x02_P2.54mm_Vertical | J3 |
| 3 | SW_Push_Dual | SW_PUSH_12mm | SW1, SW2, SW3 |
| 1 | RED | LED_D5.0mm | D1 |
| 1 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1 |
| 1 | 100k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2 |
| 1 | 100 100k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3 |
| 1 | 470 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R4 |
| 1 | 10K 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R5 |
Prezenter design files
The KiCad project lives in the onismond/Prezenter repository on GitHub; these links point at the commit this page was built from.
- LayoutPrezenter.kicad_pcb
- SchematicPrezenter.kicad_sch
- BOMPrezenter_bom.csv
Prezenter: common questions
What microcontroller does the Prezenter use?
The Prezenter is built around the DW01A, from the ESP32 family.
How big is the Prezenter PCB?
The Prezenter measures 38.1 × 69.9 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Prezenter?
13 components, from 11 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Prezenter design files?
From the onismond/Prezenter repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Prezenter design in my own project?
The repository has no license, so all rights stay with onismond. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Prezenter without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k