195 open source boards using the DW01A
Real designs built with the DW01A, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Silkscreen
iandchasse
60 × 111.3 mm171 parts2LCERN-OHL-S-2.0585ESP32
Omote
OMOTE-Community
192.4 × 50 mm135 parts2LGPL-3.0153Main
Xii-Labs
81.6 × 134.5 mm33 parts4LCERN-OHL-S-2.0102Low noise power probe
blinken
69.7 × 114.8 mm105 parts6LCC-BY-SA-4.0101ESP32
Thermal camera
Badbird5907
98 × 56 mm41 parts2LMIT55Le chiff ble
MangoIV
228.4 × 85 mm114 parts2LGPL-3.052Main
Xenii1642
81.6 × 134.5 mm33 parts4LCERN-OHL-S-2.047KlackerBS
weteor
266.5 × 99 mm149 parts2LCERN-OHL-P-2.028ESP32
Esp32InductanceMeterV2
RobieElliz
94 × 99 mm79 parts2LMIT20ESP32
LIA
JGAguado
79 × 30 mm66 parts2LCC-BY-NC-4.015ESP32
PCB CANNONBALL
user-will
25.6 × 23.6 mm58 parts4LNo license14YNXT-WM01
RJSDevel
87.6 × 35.6 mm39 parts2LGPL-3.09Bms buck boost
tor1kk
35.1 × 28.9 mm34 parts2LGPL-3.09ESP32
RadioNoob
EIectron
141.8 × 151.4 mm181 parts2LNo license8ESP32
Black-Flipper
Broccoliux
142.1 × 143 mm206 parts4LNo license7ESP32
WalkieTalkie
GuzziFlipFlops
35 × 100 mm66 parts2LMIT7ESP32
Esp32-wifi ble weighing scale
IoTReady
81.2 × 40 mm57 parts2LNo license5ESP32
Niphar
mornepousse
340.8 × 104.7 mm275 parts4LMIT4Vape light
sbyd-space
58.3 × 15 mm33 parts2LCERN-OHL-P-2.04My-Own-UPS-HAT-for-Raspberry-Pi-Zero
harshverma27
65 × 30 mm31 parts2LNo license4ESP32
CheetoPet
Cheet0sDelet0s
50.2 × 95.2 mm96 parts2LGPL-2.03ESP32
ESP32 E-Reader
IS7V4N
62.5 × 96.2 mm85 parts4LNo license3ESP8266
SHMod24
LeoDJ
49.5 × 49.5 mm64 parts2LMIT3ESP32
HearingAid ESP
AveryLion03
90.8 × 58.2 mm44 parts2LNo license3ESP8266
TWIN NODE2
MAATHES-THILAK-K
46.6 × 35.5 mm41 parts2LApache-2.03ESP32
Yunyu esp32
yunyu-x
40 × 40 mm18 parts4LApache-2.03ESP32
Esp32-pluto sdr portable
levirbl
58 × 150 mm150 parts4LNo license2ESP32
MinRead
Monacrylic
64.5 × 120.5 mm114 parts2LNo license2ESP32
Moskill
telagod
30 × 100 mm90 parts2LNo license2ESP32
Bramble
justinlindh
96 × 50 mm84 parts2LMIT2ESP32
PGR
Projeto-Guarda-Rios
67.5 × 44.4 mm75 parts4LMIT2AVR/Arduino
Salp board
aeiou642
64.8 × 58.7 mm57 parts4LNo license2ESP32
Garden133
chl33
71.1 × 39.4 mm54 parts4LMIT2FOX-JACK EXT BOARD TOP
GabeGiancarlo
51 × 21 mm29 parts2LGPL-3.02STM32
Gran-Ornament
HenrikBiscuit
25.9 × 24.2 mm19 parts2LCustom license2Nordic nRF
Orthus
Hob-dev
133.7 × 95.6 mm318 parts2LCC-BY-NC-4.01
How designs wire the DW01A
Read from the KiCad layouts of 149 open source designs, one per repository: what each pin of the DW01A connects to, and the resistors, capacitors and other passives placed on it.
- The TD pin is left unconnected on 142 of 149 designs (GND on 2, a signal on 4).
- The VCC pin has a series capacitor on 115 of 149 designs, most often 100 nF (then 1 µF).
- The GND pin has a series capacitor on 114 of 149 designs, most often 100 nF (then 1 µF).
- The CS pin has a resistor to GND on 108 of 149 designs, most often 1 kΩ (then 2 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CSpin 2 | Connected to: Signal 94% |
|
| TDpin 4 | Connected to: Not connected 95% | — |
| VCCpin 5 | Connected to: Signal 91% |
|
| GNDpin 6 | Connected to: A connector 43% · GND 17% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Silkscreen pcb by iandchasse, Omote by OMOTE-Community, Main PCB by Xii-Labs and Low noise power probe by blinken.
The DW01A in open source designs
The gallery holds 195 open source boards using the DW01A from 160 GitHub repositories; a typical one measures about 63.9 × 56.9 mm and carries around 59 components.
62% are two-layer designs, the rest use four layers or more, and 35% carry an open source license.
The most starred is Silkscreen pcb by iandchasse.
Parts used alongside the DW01A
Microcontrollers on boards using the DW01A
What boards using the DW01A are built for
DW01A: common questions
Where can I find a DW01A reference design?
Each of the 195 boards on this page is a real design using the DW01A. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the DW01A TD pin connected?
The TD pin is left unconnected on 142 of 149 designs (GND on 2, a signal on 4). Counted from the KiCad layouts of 149 open source designs using the DW01A.
How is the DW01A VCC pin connected?
The VCC pin has a series capacitor on 115 of 149 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 149 open source designs using the DW01A.
How is the DW01A GND pin connected?
The GND pin has a series capacitor on 114 of 149 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 149 open source designs using the DW01A.
What parts are used alongside the DW01A?
The TP4056-42-ESOP8, TP4056, USBLC6-2SC6, AP2112K-3.3 and MT3608 appear in the most repositories here.
Which microcontrollers do boards using the DW01A use?
Most are built on ESP32 (90), STM32 (25), RP2040/RP2350 (10) and Nordic nRF (9).
How big is a typical board using the DW01A?
The median is 63.9 × 56.9 mm, and 62% are two-layer designs.
What is the most popular open source board using the DW01A?
By GitHub stars, Silkscreen pcb by iandchasse, with 585 stars.
Can I simulate one of these boards using the DW01A before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.