OpenRemoteID
About the OpenRemoteID PCB
OpenRemoteID is an open source ESP32 PCB design by OpenDrone-hw, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 13.4 × 23.8 mm, with 6 components from 6 distinct parts.
Its main chip is the ESP32-C3-MINI-1-N4, from the ESP32 family. Other key parts include the ATGM336H-5NR-32. By type, the board carries 2 ICs, 1 switch and 1 LED.
It belongs with the rf & radio and robotics & motion designs in this gallery.
From the project
Open-source drone Remote ID hardware. Part of the OpenDrone ecosystem.
Open hardware for a standalone broadcast Remote ID module built around an ESP32-C3-MINI-1 radio module and an ATGM336H GNSS receiver.
This repository is an incomplete hardware concept, not a compliant or released product. The KiCad schematic contains six placed devices and does not pass ERC; run it for the current findings. The two-layer PCB contains the same six footprints and no routed tracks, vias or copper zones. No firmware is present.
Main components on the OpenRemoteID
OpenRemoteID bill of materials (BOM)
6 components, 6 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-MINI-1-N4 | WIFIM-SMD_ESP32-C3-MINI-1 | U2 |
| 1 | ATGM336H-5NR-32 | GPS-SMD_18P-L10.1-W9.7-P1.10-TL | U3 |
| 1 | ME6211C33M5G-N | SOT-23-5_L3.0-W1.7-P0.95-LS2.8-BL | LDO2 |
| 1 | CONUFL001-SMD-T | IPEX-SMD_3P-L2.6-W2.6-LS3.0 | RF2 |
| 1 | B3U-1000P | KEY-SMD_B3U-1000PM | SW2 |
| 1 | 16-213/GHC-YR1S1/3T | LED0402-R-RD | LED2 |
OpenRemoteID design files
The KiCad project lives in the OpenDrone-hw/OpenRemoteID repository on GitHub; these links point at the commit this page was built from.
OpenRemoteID: common questions
What microcontroller does the OpenRemoteID use?
The OpenRemoteID is built around the ESP32-C3-MINI-1-N4, from the ESP32 family.
How big is the OpenRemoteID PCB?
The OpenRemoteID measures 13.4 × 23.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the OpenRemoteID?
6 components, from 6 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the OpenRemoteID design files?
From the OpenDrone-hw/OpenRemoteID repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the OpenRemoteID design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which OpenDrone-hw chose for the repository.
Can I test firmware for the OpenRemoteID without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32Open Book Abridged Edition
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1k
ESP32Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0k
ESP32Esp32 minimal
36.2 × 26.8 mm20 parts2LMIT4.0k
ESP32Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k
ESP32Controller
29 × 74 mm58 parts4LApache-2.03.8k
ESP32Bitaxe
skot
56.5 × 99.8 mm86 parts4LCERN-OHL-S-2.01.4k