HardLabs

UP1-PM-HF

OpenKNX·OpenKNX-UP1·hardware/EDA-Files/UP1-PM-HF/UP1-PM-HF.kicad_pcb

UP1-PM-HF PCB layout, top view — open source RP2040/RP2350 board by OpenKNX

About the UP1-PM-HF PCB

UP1-PM-HF is an open source RP2040/RP2350 PCB design by OpenKNX, published on GitHub. It is a 2-layer board measuring 71 × 71 mm, with 63 components from 29 distinct parts.

Its main chip is the RP2040, from the RP2040/RP2350 family. Other key parts include the W25Q and MAX803R. By type, the board carries 25 capacitors, 20 resistors, 7 connectors, 4 diodes, 3 ICs and 1 transistor.

From the project

OpenKNX system UP1

Main components on the UP1-PM-HF

RP2040W25QMAX803R

UP1-PM-HF bill of materials (BOM)

63 components, 29 distinct parts.

QtyPartRefs
1
RP2040
U100
1
W25Q
U101
1
MAX803R
U102
1
2N7002
Q1
1
12MHz
Y100
1
LD2420 / TOFx
J10
1
VEML7700
J20
1
I2C Sensor Extension
J30
1
Extension
J40
1
Binary Inputs
J50
1
KNX_Conn
J100
1
UP1-Prog
J101
1
NanoBCU V2
GN100
1
Prog
SW100
2
MDD SM03C
D50, D51
1
LED
D101
1
RS-3535MWAR-2JYJY-J
D110
1
3300uF
C10
6
10u
C11, C12, C20, C30, C100, C109
14
100n
C50, C51, C52, C53, C103, C105, C110, C111 +6
Show 9 more
QtyPartRefs
2
33p
C101, C102
2
1u
C120, C130
3
22
R10, R107, R108
1
10k
R11
4
2k2
R50, R52, R54, R56
5
220
R51, R53, R55, R57, R106
4
1k
R101, R102, R103, R105
1
120
R110
2
33
R111, R112

UP1-PM-HF design files

The KiCad project lives in the OpenKNX/OpenKNX-UP1 repository on GitHub; these links point at the commit this page was built from.

UP1-PM-HF: common questions

What microcontroller does the UP1-PM-HF use?

The UP1-PM-HF is built around the RP2040, from the RP2040/RP2350 family.

How big is the UP1-PM-HF PCB?

The UP1-PM-HF measures 71 × 71 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the UP1-PM-HF?

63 components, from 29 distinct parts. The full bill of materials is listed on this page.

Where can I download the UP1-PM-HF design files?

From the OpenKNX/OpenKNX-UP1 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the UP1-PM-HF design in my own project?

The repository has no license, so all rights stay with OpenKNX. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the UP1-PM-HF without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

More boards in OpenKNX-UP1

Similar boards