OrcaClawController
OrcaTheWhale·The-OrcaClaw·PCBFiles/OrcaClawControllerPCB/OrcaClawController.kicad_pcb
About the OrcaClawController PCB
OrcaClawController is an open source ESP32 PCB design by OrcaTheWhale, published on GitHub under the MIT license. It is a 4-layer board measuring 80 × 22.5 mm, with 5 components from 4 distinct parts.
Its main chip is the XIAO-ESP32-C3-DIP, from the ESP32 family. By type, the board carries 2 connectors, 2 switches and 1 IC.
It belongs with the robotics & motion, iot & wireless and power & battery designs in this gallery.
From the project
Resembling (sort of) Victor's Hexclaw from League of Legends/Arcane, the OrcaClaw is a powerful(weak) arm that can be controlled remotely, and has the ability to grab and point using a laser!
This is my first ever project outside of tinkering with a breadboard and sensors. I've never modeled, made a pcb, or know a lot about assembly(hardware components, screw types). However, after a lot of work and hours done, I was able to learn a lot, and also was able to produce this project, the OrcaClaw!
What makes this unique: You will never see this in the real world(cause it's kinda useless), that's just how unique it is! Resembling a Hexclaw and an Orca, the OrcaClaw is able to be able to grab some items in your daily life! Whether you need to hold on to an empty soda can(for some…
Main components on the OrcaClawController
OrcaClawController bill of materials (BOM)
5 components, 4 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-DIP | XIAO-ESP32-C3-DIP | U1 |
| 1 | Conn_01x02_Pin | PinHeader_1x02_P2.00mm_Vertical | J1 |
| 1 | Conn_01x04 | PinHeader_1x04_P2.54mm_Vertical | J2 |
| 2 | SW_Push | SW_PUSH_6mm | SW1, SW2 |
OrcaClawController design files
The KiCad project lives in the OrcaTheWhale/The-OrcaClaw repository on GitHub; these links point at the commit this page was built from.
OrcaClawController: common questions
What microcontroller does the OrcaClawController use?
The OrcaClawController is built around the XIAO-ESP32-C3-DIP, from the ESP32 family.
How big is the OrcaClawController PCB?
The OrcaClawController measures 80 × 22.5 mm, has 4 copper layers and is 1.600198 mm thick.
How many components are on the OrcaClawController?
5 components, from 4 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the OrcaClawController design files?
From the OrcaTheWhale/The-OrcaClaw repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the OrcaClawController design in my own project?
Yes, under the terms of its MIT license, which OrcaTheWhale chose for the repository.
Can I test firmware for the OrcaClawController without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in The-OrcaClaw
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k