HardLabs

Keyboard-Doomsdaydeck

Oru-star·Doomsday-deck·PCB'S/KEYBOARD'S PCB/Keyboard-Doomsdaydeck.kicad_pcb

Keyboard-Doomsdaydeck PCB layout, top view — open source RP2040/RP2350 board by Oru-star

About the Keyboard-Doomsdaydeck PCB

Keyboard-Doomsdaydeck is an open source RP2040/RP2350 PCB design by Oru-star, published on GitHub. It is a 2-layer board measuring 189.5 × 130 mm, with 107 components from 7 distinct parts.

Its main chip is the Raspberry_Pi_Pico2, from the RP2040/RP2350 family. By type, the board carries 50 switches, 50 diodes, 6 connectors and 1 IC.

It belongs with the keyboards, dev boards & breakouts and rf & radio designs in this gallery.

From the project

A custom portable cyberdeck for computing, offline communication, electronics, and field experimentation.

A custom portable cyberdeck for computing, offline communication, electronics, and field experimentation.

These four renders show the overall enclosure concept and the carrier board from both sides.

Doomsday Deck is a custom-built, portable cyberdeck which is mde for daily computing,offline computation, and electronics experimentation all in one!!. The design uses a Orange pi zero 3w as the main sbc,7inch Display,Custom Mechanical keyboard,20000 mah battery system,RTL Sdr,A lora module,External 20Gpio pins for adding external devices or tinkering with other hardware....

Keyboard-Doomsdaydeck, from the project README
From the project README

Main components on the Keyboard-Doomsdaydeck

Raspberry_Pi_Pico2

Keyboard-Doomsdaydeck bill of materials (BOM)

107 components, 7 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
Raspberry_Pi_Pico2
U1
1
Conn_01x05
J1
2
Conn_01x02
J2, J3
1
OLED
J4
2
Conn_01x04_Pin
J5, J6
50
~
S1, S2, S3, S4, S5, S6, S7, S8 +42
50
~
D1, D2, D3, D4, D5, D6, D7, D8 +42

Keyboard-Doomsdaydeck design files

The KiCad project lives in the Oru-star/Doomsday-deck repository on GitHub; these links point at the commit this page was built from.

Keyboard-Doomsdaydeck: common questions

What microcontroller does the Keyboard-Doomsdaydeck use?

The Keyboard-Doomsdaydeck is built around the Raspberry_Pi_Pico2, from the RP2040/RP2350 family.

How big is the Keyboard-Doomsdaydeck PCB?

The Keyboard-Doomsdaydeck measures 189.5 × 130 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Keyboard-Doomsdaydeck?

107 components, from 7 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Keyboard-Doomsdaydeck design files?

From the Oru-star/Doomsday-deck repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Keyboard-Doomsdaydeck design in my own project?

The repository has no license, so all rights stay with Oru-star. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Keyboard-Doomsdaydeck without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

More boards in Doomsday-deck

Similar boards