Esp32-wled rgb controller
PaulMiron·esp32-wled-rgb-controller·hardware/proiectv2.kicad_pcb
About the Esp32-wled rgb controller PCB
Esp32-wled rgb controller is an open source ESP32 PCB design by PaulMiron, published on GitHub under the GPL-2.0 license. It is a 2-layer board measuring 48.5 × 75 mm, with 14 components from 8 distinct parts.
Its main chip is the ESP32-DevKitC, from the ESP32 family. By type, the board carries 6 resistors, 3 transistors, 1 IC and 1 connector.
It belongs with the iot & wireless designs in this gallery.
From the project
ESP32 + WLED controller for 12V RGB LED strips with IRLZ44N MOSFETs and IR remote support. KiCad project.
A simple controller board for 12V analog RGB LED strips (non-addressable, common anode), built around an ESP32 DevKitC running WLED. It supports Wi-Fi control from the WLED app/web UI and an IR remote via an onboard IR receiver header.
- Controls 12V RGB LED strips (3 PWM channels) - ESP32 DevKitC socketed on female headers (easy to replace/reflash) - Logic-level MOSFETs (IRLZ44N) driven directly from 3.3V GPIO - IR receiver input for standard 24/44-key RGB remotes - Single 12V DC input (barrel jack); 5V for the ESP32 from an external LM2596 buck module - Designed in KiCad

Main components on the Esp32-wled rgb controller
Esp32-wled rgb controller bill of materials (BOM)
14 components, 8 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-DevKitC | ESP32-DevKitC | U1 |
| 3 | IRLZ44N | TO-220-3_Vertical | Q1, Q2, Q3 |
| 1 | Screw_Terminal_01x04 | TerminalBlock_Phoenix_MKDS-1,5-4_1x04_P5.00mm_Horizontal | J2 |
| 1 | Barrel_Jack | BarrelJack_Horizontal | 12V DC |
| 1 | Conn_01x03_Pin | SolderWire-0.5sqmm_1x03_P4.8mm_D0.9mm_OD2.3mm | IRRECIEVER1 |
| 1 | Conn_01x04 | SolderWire-0.5sqmm_1x04_P4.8mm_D0.9mm_OD2.3mm | RGB1 |
| 3 | 220 | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R3, R5 |
| 3 | 10K | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2, R4, R6 |
Esp32-wled rgb controller design files
The KiCad project lives in the PaulMiron/esp32-wled-rgb-controller repository on GitHub; these links point at the commit this page was built from.
- Layouthardware/proiectv2.kicad_pcb
- Schematichardware/proiectv2.kicad_sch
- BOMREADME.md
Esp32-wled rgb controller: common questions
What microcontroller does the Esp32-wled rgb controller use?
The Esp32-wled rgb controller is built around the ESP32-DevKitC, from the ESP32 family.
How big is the Esp32-wled rgb controller PCB?
The Esp32-wled rgb controller measures 48.5 × 75 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp32-wled rgb controller?
14 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Esp32-wled rgb controller design files?
From the PaulMiron/esp32-wled-rgb-controller repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Esp32-wled rgb controller design in my own project?
Yes, under the terms of its GPL-2.0 license, which PaulMiron chose for the repository.
Can I test firmware for the Esp32-wled rgb controller without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k