Relay and-Fuse box
PJawZK·Relay-and-Fuse-box·tests/fixtures/mcp-upstream-example.kicad_sch
About the Relay and-Fuse box PCB
Relay and-Fuse box is an open source ESP32 PCB design by PJawZK, published on GitHub under the AGPL-3.0 license. It is a board, with 5 components from 5 distinct parts.
Its main chip is the ESP32-WROOM-32, from the ESP32 family. By type, the board carries 2 resistors, 1 IC, 1 connector and 1 capacitor.
From the project
A passive, serviceable relay-and-fuse power-distribution replacement concept for the Volvo 940 Turbo using Mega144H7 / EpicEFI. Design phase: research only. No PCB has been validated for vehicle use.
A passive, serviceable relay-and-fuse power-distribution replacement concept for the Volvo 940 Turbo using Mega144H7 / EpicEFI. Design phase: research only. No PCB has been validated for vehicle use.
The PDF-derived external supply and complete 20-position JP1 terminal definition are transcribed in docs/ORIGINALRELAYBOARDPDFMAP.md, including the V1.1 layout silkscreen versus V1.2 schematic/filename discrepancy. The schematic's main ECU feed is F1 (20A indicated, application-dependent) → K1 relay → CB2 RXE105 resettable polyfuse → 12 RAW / ECU. CB1 RXE110 and CB3 RXE110 also appear on the…
Main components on the Relay and-Fuse box
Relay and-Fuse box bill of materials (BOM)
5 components, 5 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-WROOM-32 | ESP32-WROOM-32 | U1 |
| 1 | Conn_01x04 | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | 100nF | C_0805_2012Metric | C1 |
| 1 | 10k | R_0805_2012Metric | R1 |
| 1 | 4.7k | R2 |
Relay and-Fuse box design files
The KiCad project lives in the PJawZK/Relay-and-Fuse-box repository on GitHub; these links point at the commit this page was built from.
Relay and-Fuse box: common questions
What microcontroller does the Relay and-Fuse box use?
The Relay and-Fuse box is built around the ESP32-WROOM-32, from the ESP32 family.
How many components are on the Relay and-Fuse box?
5 components, from 5 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Relay and-Fuse box design files?
From the PJawZK/Relay-and-Fuse-box repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.
Can I use the Relay and-Fuse box design in my own project?
Yes, under the terms of its AGPL-3.0 license, which PJawZK chose for the repository.
Can I test firmware for the Relay and-Fuse box without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k