AirSuspension
prior-philip·AirSuspension_ESP32·hardware/FCU/AirSuspension.kicad_pcb
About the AirSuspension PCB
AirSuspension is an open source AVR/Arduino PCB design by prior-philip, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 80 × 50.8 mm, with 32 components from 18 distinct parts.
Its main chip is the Arduino_Nano_v3.x, from the AVR/Arduino family. Other key parts include the LM7805_TO220. By type, the board carries 9 capacitors, 8 resistors, 5 connectors, 4 transistors, 4 diodes and 2 ICs.
It belongs with the displays & leds and sensors designs in this gallery.
From the project
AirSuspension controller running on ESP32 MCU
Controller board of the air suspension system. It carries the ESP32-S3 SuperMini, four low-side MOSFETs for the pneumatic valves, a plug-in step-down module for the 3.3 V rail, and the connectors for the OLED, the two buttons and the ride-height sensors.
- MCU: ESP32-S3 SuperMini module (U3). - Valve drivers: four IRLZ44N logic-level MOSFETs (Q1–Q4), low-side switching. Each gate has a 100 Ω series resistor and a 10 k pulldown to GND, so valves stay off while the MCU boots or sleeps. Each valve coil has a 1N4003 flyback diode to +12 V (D1–D4). - Power: 12 V input (P1/P2), 470 µF and 470 nF…
Main components on the AirSuspension
AirSuspension bill of materials (BOM)
32 components, 18 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM7805_TO220 | TO-220-3_Vertical | U1 |
| 1 | Arduino_Nano_v3.x | Arduino_Nano | U2 |
| 4 | IRLU120 | TO-220-3_Vertical | Q1, Q2, Q3, Q4 |
| 1 | Pneumatic Valves | PinHeader_1x08_P2.54mm_Vertical | J1 |
| 1 | UP/DOWN Switch | PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | OLED Display | PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | NiveauSensor | PinHeader_1x06_P2.54mm_Vertical | J4 |
| 1 | Power In | PinHeader_1x04_P2.54mm_Vertical | J5 |
| 4 | 1N4003 | D_DO-41_SOD81_P2.54mm_Vertical_AnodeUp | D1, D2, D3, D4 |
| 1 | 470uF | CP_Radial_D14.0mm_P5.00mm | C1 |
| 1 | 47uF | CP_Radial_D12.5mm_P5.00mm | C2 |
| 2 | 47pF | C_Rect_L7.0mm_W3.5mm_P5.00mm | C3, C4 |
| 1 | 10uF | CP_Radial_D5.0mm_P2.50mm | C5 |
| 1 | 47nF | C_Rect_L7.0mm_W3.5mm_P5.00mm | C6 |
| 2 | 470pF | C_Rect_L7.0mm_W3.5mm_P5.00mm | C7, C8 |
| 1 | 470uF | CP_Radial_D12.5mm_P5.00mm | C9 |
| 4 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2, R3, R4 |
| 4 | 100 | R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R5, R6, R7, R8 |
AirSuspension design files
The KiCad project lives in the prior-philip/AirSuspension_ESP32 repository on GitHub; these links point at the commit this page was built from.
AirSuspension: common questions
What microcontroller does the AirSuspension use?
The AirSuspension is built around the Arduino_Nano_v3.x, from the AVR/Arduino family.
How big is the AirSuspension PCB?
The AirSuspension measures 80 × 50.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the AirSuspension?
32 components, from 18 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the AirSuspension design files?
From the prior-philip/AirSuspension_ESP32 repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the AirSuspension design in my own project?
Yes, under the terms of its GPL-3.0 license, which prior-philip chose for the repository.
Can I test firmware for the AirSuspension without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in AirSuspension_ESP32
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k