RCU
prior-philip·AirSuspension_ESP32·hardware/RCU/RCU.kicad_pcb
About the RCU PCB
RCU is an open source PCB design by prior-philip, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 55.9 × 45.8 mm, with 18 components from 13 distinct parts.
By type, the board carries 8 connectors, 6 capacitors and 4 resistors.
It belongs with the sensors designs in this gallery.
From the project
AirSuspension controller running on ESP32 MCU
Small distribution board at the rear axle. It brings the valves and the two ride-height sensors together on one 12-pin connector (J4) that leads to the FCU. It also makes the 5 V sensor supply and divides the sensor signals down to a level the ESP32-S3 can read.
- Connector distribution: 12-pin input connector J4 (marked IP68) to the valve header J3 and the sensor header J1. - Sensor supply: a plug-in step-down module (P2–P5, marked "5V out") makes +VSens (5 V) from the 12 V line. Capacitors C1–C6 decouple the 12 V and 5 V rails. - Level shifter: each sensor signal passes a 10 k series…
RCU bill of materials (BOM)
18 components, 13 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Sensor | PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | Valves | PinHeader_1x08_P2.54mm_Vertical | J3 |
| 1 | InputConnector IP68 | PinHeader_1x12_P2.54mm_Vertical | J4 |
| 1 | Spare | PinHeader_1x01_P2.54mm_Vertical | J5 |
| 1 | + in | PinHeader_2x01_P2.54mm_Horizontal | P2 |
| 1 | 5V out | PinHeader_2x01_P2.54mm_Horizontal | P3 |
| 1 | - in | PinHeader_1x02_P2.54mm_Vertical | P4 |
| 1 | - out | PinHeader_1x02_P2.54mm_Vertical | P5 |
| 3 | 10uF | CP_Radial_D5.0mm_P2.50mm | C1, C2, C5 |
| 2 | 10nF | C_Disc_D4.3mm_W1.9mm_P5.00mm | C3, C6 |
| 1 | 10nF | C_Disc_D5.1mm_W3.2mm_P5.00mm | C4 |
| 2 | 20k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2 |
| 2 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3, R4 |
RCU design files
The KiCad project lives in the prior-philip/AirSuspension_ESP32 repository on GitHub; these links point at the commit this page was built from.
RCU: common questions
How big is the RCU PCB?
The RCU measures 55.9 × 45.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the RCU?
18 components, from 13 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the RCU design files?
From the prior-philip/AirSuspension_ESP32 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the RCU design in my own project?
Yes, under the terms of its GPL-3.0 license, which prior-philip chose for the repository.
More boards in AirSuspension_ESP32
Similar boards
Sensor smd
scottbez1
40 × 20 mm5 parts2LApache-2.04.2kSensors
StuckAtPrototype
15.2 × 9 mm14 parts4LApache-2.03.8kMicrophone
Mentra-Community
5.5 × 6.1 mm6 parts2LMIT1.2kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kPots
shanteacontrols
390 × 93 mm75 parts2LApache-2.0956USB
shanteacontrols
52 × 12.6 mm6 parts2LApache-2.0956