FCU
prior-philip·AirSuspension_ESP32·hardware/FCU/FCU.kicad_pcb
About the FCU PCB
FCU is an open source ESP32 PCB design by prior-philip, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 80 × 62.2 mm, with 37 components from 21 distinct parts.
Its main chip is the ESP32-S3-SuperMini, from the ESP32 family. By type, the board carries 10 connectors, 10 resistors, 7 capacitors, 5 diodes, 4 transistors and 1 IC.
It belongs with the displays & leds and sensors designs in this gallery.
From the project
AirSuspension controller running on ESP32 MCU
Controller board of the air suspension system. It carries the ESP32-S3 SuperMini, four low-side MOSFETs for the pneumatic valves, a plug-in step-down module for the 3.3 V rail, and the connectors for the OLED, the two buttons and the ride-height sensors.
- MCU: ESP32-S3 SuperMini module (U3). - Valve drivers: four IRLZ44N logic-level MOSFETs (Q1–Q4), low-side switching. Each gate has a 100 Ω series resistor and a 10 k pulldown to GND, so valves stay off while the MCU boots or sleeps. Each valve coil has a 1N4003 flyback diode to +12 V (D1–D4). - Power: 12 V input (P1/P2), 470 µF and 470 nF…
FCU bill of materials (BOM)
37 components, 21 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ~ | ESP32-S3-SuperMini | U3 |
| 4 | IRLZ44N | TO-220-3_Vertical | Q1, Q2, Q3, Q4 |
| 1 | Valve Power 12V | PinSocket_1x02_P2.54mm_Vertical | J1 |
| 1 | Valve Ctrl | PinSocket_1x08_P2.54mm_Vertical | J2 |
| 1 | Sensor | PinSocket_1x04_P2.54mm_Vertical | J3 |
| 1 | OLED Display | PinSocket_1x04_P2.54mm_Vertical | J4 |
| 1 | Power In | PinHeader_2x03_P2.54mm_Vertical | P1 |
| 1 | + in | PinHeader_2x01_P2.54mm_Horizontal | P2 |
| 1 | 3.3V out | PinHeader_2x01_P2.54mm_Horizontal | P3 |
| 1 | - in | PinHeader_1x02_P1.27mm_Vertical | P4 |
| 1 | - out | PinHeader_1x02_P1.27mm_Vertical | P5 |
| 1 | Buttons | PinHeader_1x03_P2.54mm_Vertical | P6 |
| 4 | 1N4003 | D_DO-41_SOD81_P2.54mm_Vertical_AnodeUp | D1, D2, D3, D4 |
| 1 | 1N4003 | D_A-405_P10.16mm_Horizontal | D5 |
| 1 | 470uF | CP_Radial_D6.3mm_P2.50mm | C1 |
| 1 | 47uF | CP_Radial_D6.3mm_P2.50mm | C2 |
| 2 | 47pF | C_Rect_L7.0mm_W3.5mm_P5.00mm | C3, C4 |
| 3 | 470nF | C_Rect_L7.0mm_W3.5mm_P5.00mm | C6, C8, C9 |
| 5 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2, R3, R4, R9 |
| 4 | 100 | R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R5, R6, R7, R8 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_Vertical | R10 |
FCU design files
The KiCad project lives in the prior-philip/AirSuspension_ESP32 repository on GitHub; these links point at the commit this page was built from.
FCU: common questions
What microcontroller does the FCU use?
The FCU is built around the ESP32-S3-SuperMini, from the ESP32 family.
How big is the FCU PCB?
The FCU measures 80 × 62.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the FCU?
37 components, from 21 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the FCU design files?
From the prior-philip/AirSuspension_ESP32 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the FCU design in my own project?
Yes, under the terms of its GPL-3.0 license, which prior-philip chose for the repository.
Can I test firmware for the FCU without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in AirSuspension_ESP32
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k