Encoder to i2c tssop20.kicad pro
prosper00·Encoder-i2c·hardware/TSSOP20/encoder-to-i2c-tssop20.kicad_pro.kicad_pcb
About the Encoder to i2c tssop20.kicad pro PCB
Encoder to i2c tssop20.kicad pro is an open source RISC-V PCB design by prosper00, published on GitHub under the MIT license. It is a 2-layer board measuring 34.5 × 33.3 mm, with 40 components from 10 distinct parts.
Its main chip is the CH32V003FXPX, from the RISC-V family. By type, the board carries 20 resistors, 12 diodes, 5 capacitors, 1 IC, 1 connector and 1 switch.
From the project
ch32v003 i2c backpack firmware to convert a rotary encoder to an i2c slave device
simple ch32v003 firmware to read a rotary encoder input device, and convert it to i2c.
Usage / notes - configured for a CH32V003 SOP8 package - encoder inputs are connected to PA1 and PA2 - encoder pushbutton is connected to PC4 - all encoder pins are externally RC debounced and pulled up [ see /hardware for schematic ] - device is configured as an i2c slave device on address 0x09. - 'read' two bytes: the first byte is the rotation value, and the second byte indicates whether the button has been pressed - values are reset to zero after a read - no software debounce or acceleration scaling…
Main components on the Encoder to i2c tssop20.kicad pro
Encoder to i2c tssop20.kicad pro bill of materials (BOM)
40 components, 10 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CH32V003FXPX CH32V003FxPx | TSSOP-20_4.4x6.5mm_P0.65mm | U2 |
| 1 | Conn | JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J1 |
| 1 | RotaryEncoder_Switch | RotaryEncoder_Bourns_Vertical_PEC12R-3x17F-Sxxxx | SW1 |
| 12 | LED | LED_D3.0mm | D1, D2, D3, D4, D5, D6, D7, D8 +4 |
| 4 | 100NF 100nF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C3, C4 |
| 1 | 10μ | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C5 |
| 3 | 100kΩ | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R3 |
| 3 | 10kΩ | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4, R5, R6 |
| 2 | ∞ | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7, R8 |
| 12 | 1k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R9, R10, R11, R12, R13, R14, R15, R16 +4 |
Encoder to i2c tssop20.kicad pro design files
The KiCad project lives in the prosper00/Encoder-i2c repository on GitHub; these links point at the commit this page was built from.
Encoder to i2c tssop20.kicad pro: common questions
What microcontroller does the Encoder to i2c tssop20.kicad pro use?
The Encoder to i2c tssop20.kicad pro is built around the CH32V003FXPX, from the RISC-V family.
How big is the Encoder to i2c tssop20.kicad pro PCB?
The Encoder to i2c tssop20.kicad pro measures 34.5 × 33.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Encoder to i2c tssop20.kicad pro?
40 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Encoder to i2c tssop20.kicad pro design files?
From the prosper00/Encoder-i2c repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Encoder to i2c tssop20.kicad pro design in my own project?
Yes, under the terms of its MIT license, which prosper00 chose for the repository.
Can I test firmware for the Encoder to i2c tssop20.kicad pro without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RISC-V firmware against it before you order a PCB.
More boards in Encoder-i2c
Similar boards
RISC-V
Audio
byrantech
27.8 × 22.3 mm38 parts2LMIT4.3kRISC-V
Keybit
notaroomba
19.1 × 19.1 mm19 parts2LNo license438RISC-V
Workbench-1 Controller
Quchaosheng
160 × 130 mm106 parts8LApache-2.0212RISC-V
Froggyswadge
cnlohr
81.5 × 72.2 mm92 parts2LMIT105RISC-V
Keytartouch
cnlohr
152.5 × 117.5 mm69 parts2LMIT105RISC-V
Ch32v003f4u6 with wsled
cnlohr
40.6 × 44.5 mm26 parts2LMIT105